查询词典 leftover of bolt of cloth

Unlike the famous standard Mauser cation, the Gehmann bolt has cocking handle near the front end of the bolt, and the receiver has a split bridge.

与著名的标准毛瑟阳离子的Gehmann螺栓已握把附近螺栓的前端，并接收了一些分裂的桥梁。

It is quite complex and difficult to simulate bolt pretension accurately in the analysis of bolt joint by finite element method.

在螺栓联接的有限元分析中准确模拟螺栓的预紧力是一项复杂而困难的工作。

Frame assembly finite element model and optimization design model of rolling press were established by the use of APDL language,adopting the degree of freedom manner of coupling node to deal with the bolt and pin shaft joint between each component of frame assembly,and at the same time take the prestressing force of bolt joint into consideration by adopting the temperature dropping method.

利用APDL语言，建立了辊压机机架有限元模型与优化设计模型，采用耦合节点自由度的方式处理机架各部件间的螺栓和销轴联接，同时对螺栓联接的预应力，采用温降法加以考虑。

The APS itself is a relatively crude, smoothbore arm, with a gas operated, rotating bolt action, fired from an open bolt.

APS的本身是一个比较粗糙，膛臂，以天然气经营，旋转螺栓行动，从一个开放的螺栓被解雇。

Level the body assembly until the short end of the bolt can also fit into the rocker panel hole (Figure 3). Tighten the flange nut, using a 24mm or 15/16 socket or wrench - the base will center the bolt.

校平主体总成，直到螺栓的较短一端也能配合进摆杆面板孔（图3）用24mm或15/16的套筒或扳手拧紧法兰的螺母－底座将对中心于螺栓。

4 Components in the guide ring seat surface, and to maintain stem vertically in a clean work surface; 4.5 Lubrication and installed on top of the spring washer bearings and bearing connecting rings, and lubricating the bottom of the spring washers, valve cover and gasket components will be placed in position inside the valve cover; 4.6 will regulate the bolt lock nut bolt screw to adjust the top.

4.4 将组件座于导环面上，并保持阀杆垂直地处于清洁的工作面上； 4.5 润滑并在顶部弹簧垫圈上安装轴承和轴承连接环，和润滑底部弹簧垫圈，将阀盖及垫圈组件放在阀盖内的位置上； 4.6 将调节螺栓锁紧螺母拧到调节螺栓的顶部。

Based on active timbering principle of bolt-grouting, shearing strength between bolt-grouting and rock can be transformed into the surface pressure of acting on the inner surface in the cavity and anchor-forced rock is regarded as a equivalent material.

3基于锚杆的主动支护原理，将锚杆与岩体之间的剪应力转换为作用在洞室内表面上的面压力，将锚固后的岩体视为等效材料。

In order to ensure the reliability of flywheel bolt connection,stress analysis of bolt is performed u- sing contact analysis method.

为了确保飞轮螺栓连接的可靠性，采用接触分析法对螺栓进行了应力分析。

The engineering facilities service mainly take JIAOMEITE,DACROMET series spreading equipment as the leadership,it is good at development and production of special-purpose spreading equipment by spare parts for car,for example the automobile brake disc,braking,muffler,exhaust,oil pipe,U shape bolt,deep hole bolt and so on the special product special purpose equipment.

工程设备业务主要以焦美特、达克罗系列涂覆设备为主导，尤以汽车零部件专用涂覆设备的开发、生产见长，譬如汽车刹车盘、制动毂、消声器、排气管、油管、U形螺栓、深孔螺栓等特殊产品的专用设备。

My first job was to cock my crossbow, take a biopsy bolt from the cooler that served as ammu nition box, nock the bolt, and then remove the sheath of aluminum foil protecting the tip from contamination by extraneous DNA.

我的第一项任务就是装配弓弩：从铝制的冷藏盒中取出箭，架在弩机上，然后取下防止箭头被外源DNA污染的铝箔鞘。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48