英语人>网络例句>lean 相关的网络例句
lean相关的网络例句
与 lean 相关的网络例句 [注:此内容来源于网络,仅供参考]

Carcass length, eye muscle area, lean percent, meat color score, marbling score and intramuscular fat of Duroc×LUYAN white pig were higher, increased by 1.81%, 15%, 1.07%, 6.85%, 18.46% and 178.57% respectively; fatback, water loss rate and drip loss reduced by 14.35%, 70.51% and 63.70% respectively as compared with Yorkshire×LUYAN white pig.

其中,杜×鲁烟组合的胴体直长、眼肌面积、瘦肉率、肉色、大理石纹评分和肌内脂肪较高,分别比大×鲁烟组合提高1.81%、15%、1.07%、6.85%、18.46%和178.57%;背膘厚较薄、失水率和滴水损失较低,分别比大×鲁烟降低14.35%、70.51%和63.70%。

The result also indicated that the eurhythmics exercise can make the fat of body decrease, increase the lean body mass and the lower limb flexibility, and control group isn' t obviously change.

行走时,步宽较大,身体重心左右偏移的幅度相对较大。通过练习,学生的三围较实验前更接近标准,身材更加健美

That said, though, many Ecstatics lean toward some combination of drugs and music.

而且有不少教徒同时借助毒品和音乐的力量。

Be responsible for implementation lean production in Manufacturing Dep.

负责在本部门推行精益生产模式。

Be responsible for implementation lean production in Logistics Dep.

负责在本部门推行精益生产模式。

Be responsible for implementation lean production in QA Dep.

负责在本部门推行精益生产模式。

How to apply Lean Six Sigma in driving results in bottoms up economics?

在自下而上的经济环境中如何运用精益六西格玛来驱动结果?

Plus it has a good amount of lean protein from the egg and the Canadian bacon.

另外,它还有数目可观的鸡蛋当中的精益蛋白质(或瘦蛋白质:lean protein)和加拿大熏猪肉。

Du Bos and Croce lean towards the pleasure of feeling.

这样的办学导向,我认为肯定是不正确的。

It's a lean meat, and you can have it with a…English muffin, some oatmeal, and sprinkle some raisins on top.

这是一块瘦肉,你还可以吃一块英格兰式松饼、一些燕麦粥并且在上面撒上一些葡萄干。

第104/105页 首页 < ... 97 98 99 100 101 102 103 104 105 > 尾页
相关中文对照歌词
Lean Back (Remix)
Lean Back (Remix)
Lean Molly
Gangsta Lean
Molly With That Lean
Lean On Me
Lean On Me
Lean Back
Nothing Left To Do
Lean On Me
推荐网络例句

Based on the relationship and the phenomenon model, an improved model of MR damper has been presented in this paper.

摘 要:本文在实验数据的基础上建立了磁流变阻尼器输出力与不同常电流控制量的关系,对现有的 p模型进行了改进。

I don't think our founding fathers were very fuckable.

我认为我们的开国元老没什么吸引力

In chapter 3, an optimum method of milling parameter based on orthogonal cutting finite element model is proposed.

第三章提出了基于正交切削加工有限元模型的铣削参数优化方法。