查询词典 layer-out

There is thermal keeping layer in the heater and vaporizer. The enclosure of the thermal keeping layer is made of thin plate of stainless steel. The surface is underwent the process-sing of specula technology and dark brightness.

外形美观。加热器、蒸发器外面均设有保温层，保温层外用不锈钢薄板制作外壳，表面做镜面或亚光处理。

The experiment results indicate that a hardened layer is obtained on the surface of the materials after two kinds of surface hardening. Microstructure of the hardened layer is fine spiculate martensite which can help to improve the wear and friction properties of the materials.

研究结果表明：经2种表面淬火后，材料的表面得到一均匀的硬化层，其组织为细针状的马氏体组织，材料表面的耐磨性和摩擦系数得到了显著的改善。

The results showed that the blending system could form surface gel and internal spumescent char layer to achieve flame retardant properties.The flame retardant properties of flame resistant PA6 contenting TPMP/MA complex system were studied by LOI,UL-94 and cone calorimeter tests.The results showed that the LOI value of PA6/17%MA system was 27.2,and the LOI value of PA6/4%TPMP/13%MA system was 28.6.The UL-94 test was V-0 level.The flame retardant mechanism analysis indicated that the TPMP/MA complex system could form thick intumescent char layer to execute the flame retardant functions both in the condensation phase and the gas phase.

将阻燃剂TPMP、MA复配后添加到PA6中，通过采用LOI、垂直燃烧及锥型量热仪研究了体系的阻燃性能，PA6/17%MA体系的LOI值为27.2，PA6/4%TPMP/13%MA体系的LOI值达到了28.6；上述体系的垂直燃烧性均为V-0级，对阻燃机理的分析表明，TPMP与MA复配应用时，可形成膨胀的较厚炭层，在气相和凝固相共同发挥阻燃作用。

In addition, a printing plate edge marked slopes or plate is too thin, or short-run printing of excessive wear lighter, so that the short-run suites and whitespace differences of high and low is too low and too soft pads, resulting in suites blank areaand, electro-chemical layer of aluminum foil, etc, should be made at the edge version slope near 90-degree right-angle (such as seihan with carving techniques that help you make little gradient edge version), according to the characteristics of the short-run suites, with thickness larger plate seihan, and a blank site, using a corrosion deeper stereoplasm lining for short-run; in addition, you should choose thin aluminized layer of anodized, adjust the appropriate business card printing and membership card making and adjusted pressure volume drum uponsize pressuer letoff drum.

此外，印版边沿存在明显的斜坡度或版材太薄，或印版过量烫印磨损变浅，使烫印版面与空白的高低差异太小，衬垫材料过软，造成版面空白部位与电化铝箔层接触等，应将版边沿坡度制成近90 度的直角(如采用雕刻工艺进行制版，可使版边沿几乎没有坡度)，根据烫印版面的特点，采用厚度大一些的版材制版，并将空白部位腐蚀深一点，采用硬质包衬进行烫印；此外，应选择镀铝层较薄的电化铝，调整合适的制卡和会员卡制作压力，并适当调整压卷滚筒压力和收卷滚筒拉力。

There is an active growth layer and super cooled water exists with ice crystals that may be an important feature layer to occur rain in stratiform cloud.

过冷水滴和冰晶共存层存在，且冰晶活跃增长，此层的存在可能是发生降水的关键。

After observing the specimens from JMA-m groups, we have found that epithelium and endothelium of cornea full, the lesion are light edema at stromatic layer. One small amount of inflammatory-cell infiltrate presents the collagen fiber lack of rules at shallow stromatic layer.

观察角膜安的结果表明，中药中剂量组角膜上皮和内皮层完整，基质轻度水肿，浅基质层内少量炎性细胞浸润，胶原纤维走行欠规则，整体改变较低剂量组减轻。

The electroluminescence devices (ITO/NPB/emitting layer /BCP/Mg : Ag) based on 1, 4-bis (4-N, N-methylamino styryl) naphthalene as emitting layer have been designed by the energy band matching principle.

以自制的&D-π-D&对称型有机绿色发光分子1，4-双（4'-N，N-二甲基氨基苯乙烯基）萘为发光层，在结构为ITO/NPB/BMABN/BCP/Mg： Ag的器件中，研究了空穴阻挡层厚度对器件发光性能的影响。

First layer of skin from the fascia on the separation layer down, the entire leg of the subdermal vascular network exposure.

首先将皮肤层从浅筋膜层上分离下来，使整个小腿的真皮下血管网暴露。

The site that is located on the eminence of nose structure, and far-source the underwater distributary channel and estuary bar experiencing the late dagenetic period B is the most promising for accumulation of oil and gas. Vertically, late diagenetic period B sand layer is advantageous for oil and gas gathering, while late diagenetic subperiod A3 sand layer is disadvantageous for oil and gas gathering.

平面上处于鼻状构造高部位，又处于晚成岩B期的远源水下分流河道、河口坝是最有利于油气富集的部位；纵向上，晚成岩B期的砂体有利于油气聚集，而晚成岩A3亚期的砂体不利于油气聚集。

The results showed that: During the process of ion sulphurization, the main formation mechanism of sulphide layer is that the elemental sulphur diffuses inward the substrate along its defects, the composition of substrate has a certain effect on the formation process of sulphide layer.

结果表明：在离子渗硫过程中，渗硫层的形成是以硫沿基体缺陷向内部扩渗为主导机制，基体成分对渗硫层的形成过程有一定影响。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失