查询词典 lateral axle

The automobile axle locking nut was split in the assembly. The fatigue cause was analyzed through macroscopic fracture, microstructure, electron probe and hardness surveys.

某公司生产的汽车半轴锁紧螺母在装配时被拧裂，用宏观断口、金相观察、电子探针及硬度测量等方法对其断裂原因进行分析。

The main products are car-axis, farm axles, axle series of spline shaft and the PCS series of crushing machine and ancillary equipment.

主要产品有汽车轴、农用车轴、工程车轴等系列花键轴及PCS系列破碎机及配套设备。

Planetary assembly consists of the planetary gears and the drive sun gear which spline connected with the axle shaft.

太阳轮为主动件，和半轴以花键连接。

This article elaborated a 12 level of rotational speed C6132 horizontal lathe headstock design process, the headstock uses to support the main axle and to cause it revolving.

本文阐述了一个12级转速的C6132卧式车床主轴箱的设计过程，主轴箱用以支撑主轴并使之旋转。

In the pump body installed a stator swing span and a swing span rotation shaft, the swing roller bearing on the stator swing span connects with an end of the stator mount, the other end of the stator mount connects with the stator; on the plunger connecting rod sliding boot installed a static pressure balance chamber, the holding rings are arranged on the two sides of the plunger connecting rod sliding boot which has a fit clearance with the holding rings; the rotor rotates the stator simultaneously via the plunger piston; the needle roller bearings are arranged on the two inner circles and fit with the port axle.

在泵体内安置有定子摆架和摆架转轴，位于定子摆架上的摆架滚子轴承与定子托架的一端配合联接，定子托架的另一端与定子相连；柱塞连杆滑靴上设有静压平衡室，柱塞连杆滑靴两侧设有保持环，柱塞连杆滑靴与保持环有一定的配合间隙；转子通过柱塞带动定子同步旋转；在转子内圆两端设有滚针轴承，滚针轴承与配流轴配合。

After slip column and slip sleeve were substituted for axle hearing and orbit, failure vanished, utilization ratio of equipment and quality of products were raised.

通过重新设计计算。采用滑柱滑套结构替代原轴承和导轨条结构后。原有故障形式被消除。大大提高了设备利用率和产品质量。

Behind the cabin, positioned in front of the rear axle, is the V8 FSI engine, a sculptured piece of engineering visible both through the large, shield-shaped rear window and from inside the car.

机舱后面，在后轴前方，是V8 FSI发动机，有形的工程雕塑作品都通过大，盾形的后窗和车内。

The first to use PRO / E software components establishment of the body (body, cylinder head, cylinder pad, cylinder liner, the main bearing caps, Flywheel carcasses, gear Connection Board Room, Shell pump, oil pan, about mounting frame, rear axle oil blocks, etc.) 3D solid model; Then use Hypermesh software division finite element mesh to ensure a good grid quality, and better coordination of the grid between quantity and accuracy of contradictions; Finally using ANSYS software components of a body finite element analysis.

首先利用PRO/E软件建立机体组件（机体、气缸盖、气缸垫、气缸套、主轴承盖、飞轮壳、齿轮室连接板、水泵壳体、油底壳、左右悬置支架、后轴油封盖等）的三维实体模型；然后利用Hypermesh软件划分有限元网格，保证了良好的网格质量，较好地协调了网格数量和计算精度之间的矛盾；最后利用ANSYS软件对机体组件进行了有限元分析。

The CDYM-2-02 preselection machine for the gasket of main reducer s shell is introduced, which is fitted on the new flexible assembly line of the main reducer of automobile s rear axle.

介绍了一种新型汽车后桥主减速器柔性装配线中配备的 CDYM-2 -0 2型主减速器壳体垫片预选机。

Our company main production: iron bridge shell assembly, welding bridge-shell and axle assembly, flywheel ring assembly, planet-assembly, automotive brake assemblies and reducer shell, shell, and so clutch Class chassis products, mainly for the FAW Group, the firewood, Green gas, special Liu, Zhu Jichang, such as supporting the Yellow Sea, in supporting the production capacity to more than 100,000 copies.

我公司主要生产：铸铁桥壳总成、冲焊桥壳及桥总成、飞轮齿环总成、行星架总成、汽车制动器总成及减速器外壳、离合器外壳等底盘类系列产品，主要为一汽集团、大柴、青汽、柳特、黄海等主机厂配套，年生产配套能力可超过10万辆份。

The production moved off-Broadway to New York City, where she won the Joseph E. Calloway award for her performance, and was profiled in American Theater Magazine as one of ten young theater artists to watch.

生产提出过百老汇的新的纽约市，在那里她赢得了约瑟夫calloway奖，她的表现，并于异型在美国的战区杂志之一， 10战区的青年艺术家观赏。

It's a risk tradeoff, and I believe that adding test support code usually wins.

这是一个风险的权衡，我相信添加测试代码通常会占上风。