查询词典 kw.

Agglomeration ignites test result makes clear, temperature of microwave sirocco ignition nods igneous temperature under agglomeration of traditional iron ore far, in temperature of wind of 1.5 min of 8 kw of microwave output power, ignition, warm-up 350 ℃ fall can acquire the agglomeration ore deposit with good target.

烧结点火试验结果表明，微波热风点火温度远远低于传统铁矿烧结点火温度，在微波输出功率8 kw、点火1.5 min、预热风温度350℃下可获得指标良好的烧结矿。

Application of the vertical structure over a wide range of power of 7.5 ~ 132kW; when the drive power exceeding 160 kW, the use of horizontal structures.

其立式结构的应用较广泛，功率为7.5~132kW；当驱动功率超过160 kW时，采用卧式结构。

Consider a requirement for an amplifier having a voltage gain of 10 at 50 kHz driving into a 10 kW load.

考虑对于一个在50 kHz频率上电压增益为10的放大器驱动10 kW负载时的要求。

At low heat flux, the results show that the heat transfer coefficients of mono and biporous surfaces are up to 120 and 70 kW/m2K, respectively.

实验结果显示，单孔与双孔径毛细结构的热传系数最高可达120 与70 kW/m2K。

RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，TiZr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，TiZr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

RESULTS摘要: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果摘要：在激光功率和光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，TiZr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

The microstructure of Ti Zr alloy formed under this suitable technologic parameter matching was analyzed by scanning electron microscope. RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，Ti Zr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

The energy sources to operate the drying room are 692 m3 Natural Gas and 19,3 KW/h Electricity for one drying cycle (dryingon 19.11.01 read off by Herby Dunn or refer Appendix VIII, Embodied Energy Rapid Wall, drying room).

运行一个干燥工序的干燥室的能源是692 m3 的天然气和19，3 KW/h的电（01年11月19日的干燥，由荷尔比·顿读取或参照附件VIII，速成墙体现能，干燥室）。

The results showed that the optimum operating parameters for steaming treatment were as follows: temperature was 95℃, time was 60 s, for tunnel-type drying production line, the loadage was 5.0 kg/m2, hot air temperature was 85℃, wind speed was 1.5 m/s, and for industrial microwave drying production lines, material thickness was 15 mm, drying power was 16 kW, drying time was 90 s.

结果表明，在蒸汽温度95℃，汽蒸时间60 s；隧道式干燥生产线装载量5.0 kg/m2，热风温度85℃，风速1.5 m/s；微波干燥生产线铺料厚度15 mm、干燥功率16 kW、干制时间90 s的条件下，所生产的干制黄花菜经农业部食品质量监督检验测试中心检测其感官、理化和微生物指标均达到了《无公害食品—干制金针菜》NY5186－2002所规定的一级品标准。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。