查询词典 kempers

As for the mesh screen type, its volume multiplied by 100% its porosity was the desirable filling amount. Having considered the forgoing findings, the researchers add up the amounts of the above two types as the filling amount of the composite micro structure, with the filling fluid being acetone. In fabricating the heat spreader, a copper pipe is added to serve the filling purpose. What is more, because the manufacturing process is not carried out in a totally clean environment, there is some noncondensible gas left, which will have a negative effect on the performance of the heat spreader. Consequently, the copper pipe has to be reserved so that the exhaust gases can be evacuated after the filling is done.

Kempers 文中可知，沟槽结构之填充量以微结构体积之80%为最佳，网格结构则是以网格体积乘上孔隙率(porosity，φ)之100%为最佳，故本研究便以两者之加总做为复合式微结构之填充量，填充液为丙酮；在均温基板之制造程序中，会加装一铜管做充填之用，且而由于制造过程并非于一完全干净之环境下完成，故板内会有一些不利于均温基板作用之非凝结性气体noncondensible gas (NCG残留，因此铜管需保留一定的长度，以方便充填完成后将废气排出之用。

Kempers' study , the more layers the mesh screen type had, its resistance against gravity was higher, but its heat resistance and flow resistance were comparatively augmented. As mentioned in the preceding paragraph, it is extremely difficult for a single micro structure based on any of the three types to possess both low flow resistance and strong capillary force. Faced with this fact, the researchers have tried to mix the three micro structures in Table 2 into as many combinations as possible so that a composite micro structure with low flow resistance and great capillary force may be fabricated. After a thorough analysis, the groove combined with sintered metal or mesh screen has been found to be a better alternative. However, the groove combined with sintered metal will raise the flow resistance of the channel, and the aluminum substrate employed in this research cannot be sintered into a micro structure. As a result, the groove combined with mesh screen is finally chosen as the composite structure to enhance its capillary force and at the same time maintain its high permeability. In this way, the heat pipe will not fail due to the working angles.

Kempers 的研究当中提到，当网格结构越多层时，其对抗重力的能力也越强，但相对的其热阻以及流阻也越高，就如同前段所述，我们很难在单一结构当中找出一流阻低且毛细力之微结构；因此本研究便以表2中之三种微结构进行组合，找出一低流阻且毛细力强之复合式结构，经分析发现，沟槽搭配烧结以及沟槽搭配网格为较佳之组合方式，但由于烧结搭沟槽构造将会提高流道之流阻，且本研究使用铝做为基材，并无法使用烧结最为其微结构，故将采用网格搭配沟槽之复合式结构提高结构的毛细力，并维持沟槽结构的高渗透性，解决因角度造成热管失效的问题。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。