查询词典 joint

Knee Joint Tilting Mechanism:Tilting Occurs at the Front or at the Knee Joint Position of the Chair Seat,and This Mechanism Supports Different Tilting Positions When the User Lean Backwards or Forwards

足膝平衡倾仰机关：此机关置于座位前端或接近足膝关节处，当使用者在不同位置倾仰时，此机关能提供适当的支持

The research indicate that the performance of brazing joint using Al-Ge-Si brazing filler metal precedes to the one using HL401 brazing filler metal. And the main reason is that brittle compound such as Cu2Al is not appeared in brazing joint.

本研究建立的2090Ce铝锂合金钎缝组织形态成长模型以及母材溶解厚度控制模型对钎料的选择、钎焊工艺参数的选择及接头钎焊间隙的确定等具有重要的参考和指导作用。

The result indicated that the stress was concentrated on the end of the joint interface and inner filler metal. If brittle intermetallics were produced in these areas, the fracture of joint would occur frequently.

通过采用Marc非线性有限元软件，对接头区在冷却过程中的应力变化、应力分布及裂纹敏感区域等进行了分析。

Compared with the joint brazed with Cu-Ti filler metal, the content of Cu in the reaction layer adjacent to the stainless steel is higher than the joint brazed with Cu-Co-Ti filler metal, so is the content of Nb in brazing seam.

与Cu-Ti钎料接头相比，Cu-Co-Ti钎料接头中钎缝与不锈钢侧的反应层中Cu含量较高，钎缝中Nb含量也较高。

The mechanical properties and microstructure of the joints joined by the new developed filler metal and TC18 filler metal were compared,the results showed that only the strength of the joint joined by TC18 filler metal was satisfied,while the comprehensive mechanical properties of the joint joined by the developed filler wire were ideal.

对采用研制的焊丝和采用TC18同质焊材钨极氩弧焊焊接TC18钛合金的接头力学性能及微观组织进行了对比研究，结果表明：采用同质焊材焊接TC18钛合金只能保证接头的强度指标，而采用研制的新型焊丝焊接TC18钛合金，可以保证接头具有优良的综合力学性能。

The results show that the spreading area of series Ni-P filler metal increases with the increase of brazing temperature, and the spreading areas of Ni-P filler metal is larger than that of Ni-Cr-P filler metal; the shear strength of the brazed joint at room temperature increases with the increase of temperature from 925℃ to 1000℃, and the shear strength of the stainless steel joint brazed with Ni-P filler metal is superior to that with Ni-Cr-P filler metal by 30~40 MPa in the same brazing technology.

结果表明，Ni-P系钎料铺展面积随钎焊温度的升高而增大，并且相同温度下不含Cr的Ni-P钎料铺展面积大于Ni-Cr-P的铺展面积；钎焊温度从925 ℃升高到1000 ℃过程中，Ni-P、Ni-Cr-P钎料钎焊不锈钢接头的室温剪切强度均增大，并且在相同钎焊工艺下，不含Cr的Ni-P钎料钎焊不锈钢接头室温剪切强度优于Ni-Cr-P钎焊接头强度30~40 MPa；Ni-P系钎料钎焊接头高温强度随温度升高而下降，测试温度超过500 ℃时，相同温度下含Cr的钎料能够提高钎焊接头强度0~30 MPa。

For the transparency, The vertical jointing profiles between adjacent panes of glass are made of extra transparent joint gap. This joint gap is designed 8mm to ensure the stability as well as the transparency.

为不影响隔墙的整体透明效果，在相邻的玻璃板之间可采用高透明的连接型材；在保证强度的前提下将型材截面宽度设计成8毫米，使玻璃隔墙保持了高度的通透效果。

Maximum gap of the joint between the two parts of the interior chamber of a test apparatus which,when the internal gas mixture is ignited and under specified conditions,prevents ignition of the external gas mixture through a 25 mm long joint,for all concentrations of the tested gas or vapour in air.

测试设备内室两部分之间连接部的最大间距，当内部气体在指定条件下点燃时，它能在所有测试气体或空气中蒸汽的浓度下，阻止经由25mm长的间接部引起的外部混合气体的着火。

Maximum gap of the joint between the two parts of the interior chamber of a test apparatus which,when the internal gas mixture is ignited and under specified conditions,prevents ignition of the external gas mixture through a 25 mm long joint,for all concentrations of the tested gas or vapour in air.

测试仪器的内腔两部分之间的最大的间隙是25mm，用于在内部混合气体点火时防止外部气体点着，适用于所有的测试气体或空气中的水蒸气。MESG是混合气体的一个特性参数。

Maximum gap of the joint between the two parts of the interior chamber of a test apparatus which,when the internal gas mixture is ignited and under specified conditions,prevents ignition of the external gas mixture through a 25 mm long joint,for all concentrations of the tested gas or vapour in air.

2重叠的两端都被担保的标本在75毫米以上部分的125标志压敏胶带。3为标本，在他们不是围下端的捏时，上端就是appllied本着纵轴的标本

And discuss some key point of integrated management system design, include hazard identification and risk assessment and risk control in the occupational health and safety management, the measure of satisfaction target of customer, the flawlessness of law system, the integration of the integrated management system and enterprise standardization system, unify lead institution and work orgnization, integreted internal audit and integrated management review.

同时，论述了一体化管理体系构建中的几个主要问题，包括职业健康安全管理中的危险源辨识、风险评价和风险控制、顾客满意度的科学监测、法律、法规体系的完善、一体化管理体系与企业标准化体系的有机结合、统一的领导机构和工作机构、一体化的内部审核和管理评审。

Deepwater Taranaki is investigated for its petroleum potential, using all available seismic data tied to shallow-water wells.

运用与浅水井相关的现有全部震波探测数据考察了深海区塔拉纳基盆地的油藏前景。