查询词典 joint

The result indicated that the stress was concentrated on the end of the joint interface and inner filler metal. If brittle intermetallics were produced in these areas, the fracture of joint would occur frequently.

通过采用Marc非线性有限元软件，对接头区在冷却过程中的应力变化、应力分布及裂纹敏感区域等进行了分析。

Compared with the joint brazed with Cu-Ti filler metal, the content of Cu in the reaction layer adjacent to the stainless steel is higher than the joint brazed with Cu-Co-Ti filler metal, so is the content of Nb in brazing seam.

与Cu-Ti钎料接头相比，Cu-Co-Ti钎料接头中钎缝与不锈钢侧的反应层中Cu含量较高，钎缝中Nb含量也较高。

The mechanical properties and microstructure of the joints joined by the new developed filler metal and TC18 filler metal were compared,the results showed that only the strength of the joint joined by TC18 filler metal was satisfied,while the comprehensive mechanical properties of the joint joined by the developed filler wire were ideal.

对采用研制的焊丝和采用TC18同质焊材钨极氩弧焊焊接TC18钛合金的接头力学性能及微观组织进行了对比研究，结果表明：采用同质焊材焊接TC18钛合金只能保证接头的强度指标，而采用研制的新型焊丝焊接TC18钛合金，可以保证接头具有优良的综合力学性能。

The results show that the spreading area of series Ni-P filler metal increases with the increase of brazing temperature, and the spreading areas of Ni-P filler metal is larger than that of Ni-Cr-P filler metal; the shear strength of the brazed joint at room temperature increases with the increase of temperature from 925℃ to 1000℃, and the shear strength of the stainless steel joint brazed with Ni-P filler metal is superior to that with Ni-Cr-P filler metal by 30~40 MPa in the same brazing technology.

结果表明，Ni-P系钎料铺展面积随钎焊温度的升高而增大，并且相同温度下不含Cr的Ni-P钎料铺展面积大于Ni-Cr-P的铺展面积；钎焊温度从925 ℃升高到1000 ℃过程中，Ni-P、Ni-Cr-P钎料钎焊不锈钢接头的室温剪切强度均增大，并且在相同钎焊工艺下，不含Cr的Ni-P钎料钎焊不锈钢接头室温剪切强度优于Ni-Cr-P钎焊接头强度30~40 MPa；Ni-P系钎料钎焊接头高温强度随温度升高而下降，测试温度超过500 ℃时，相同温度下含Cr的钎料能够提高钎焊接头强度0~30 MPa。

For the transparency, The vertical jointing profiles between adjacent panes of glass are made of extra transparent joint gap. This joint gap is designed 8mm to ensure the stability as well as the transparency.

为不影响隔墙的整体透明效果，在相邻的玻璃板之间可采用高透明的连接型材；在保证强度的前提下将型材截面宽度设计成8毫米，使玻璃隔墙保持了高度的通透效果。

Maximum gap of the joint between the two parts of the interior chamber of a test apparatus which,when the internal gas mixture is ignited and under specified conditions,prevents ignition of the external gas mixture through a 25 mm long joint,for all concentrations of the tested gas or vapour in air.

测试设备内室两部分之间连接部的最大间距，当内部气体在指定条件下点燃时，它能在所有测试气体或空气中蒸汽的浓度下，阻止经由25mm长的间接部引起的外部混合气体的着火。

Maximum gap of the joint between the two parts of the interior chamber of a test apparatus which,when the internal gas mixture is ignited and under specified conditions,prevents ignition of the external gas mixture through a 25 mm long joint,for all concentrations of the tested gas or vapour in air.

测试仪器的内腔两部分之间的最大的间隙是25mm，用于在内部混合气体点火时防止外部气体点着，适用于所有的测试气体或空气中的水蒸气。MESG是混合气体的一个特性参数。

Maximum gap of the joint between the two parts of the interior chamber of a test apparatus which,when the internal gas mixture is ignited and under specified conditions,prevents ignition of the external gas mixture through a 25 mm long joint,for all concentrations of the tested gas or vapour in air.

2重叠的两端都被担保的标本在75毫米以上部分的125标志压敏胶带。3为标本，在他们不是围下端的捏时，上端就是appllied本着纵轴的标本

The contact condition of cement concrete 's face plate with denudation affect not only road's joint space and joint gap, but also road's early stage cracking.

水泥混凝土面板与基层接触状况不仅影响路面接缝间距和接缝宽度，同时也对路面早期开裂产生影响。

Considering the prerequisite of joint non-linearity and glue-line elasto-plasticity,the stress distributions in the glue-line of asymmetrical joint for continuous or gap jointing were analyzed by finite element method and glue-line structure optimization was made.

在考虑接头非线性和胶层弹塑性的前提下，利用有限元方法分析了连续胶层不对称接头和间隙连接不对称接头中胶层内的应力分布情况，并在此基础上对胶层结构进行优化。

You can snipe the second and third union leaders from this position.

您可以鹬第二和第三工会领袖从这一立场出发。

Aiming at the currently shortage of XML streams quality detecting, this paper proposes a new forecasting method of XML streams quality by least squares support vector machines, which is used the method of XML keys' vector matrix as windows, and vector product wavelet transform to multilevel decompose and refactor the XML streams series, that can fulfill real-time checking demand of XML quality, and ensure constraint, consist- ency and integrality. For even more adapting net load, it proposes a control strategy by weight and adaptive adjustment to ensure XML streams quality.

针对当前XML数据流质量检测存在的不足，提出构建XML键的矢量矩阵作为窗口，利用矢量积小波变换多级分解与重构XML数据流，再结合最小二乘支持向量机对XML数据流质量进行预测的一种方法，满足XML数据流质量重构时实时检测的要求，保证XML数据的约束性、一致性与完整性；为了更好的适应网络负载，采取加权与自适应窗口调整等调度策略充分保证XML数据流的质量检测。