查询词典 joint

CT is enraged - the diagnosis that iodic double comparative radiography conduces to humeral joint injuring, it is important to be the medical jurisprudence appraisal that humeral joint injures to offer video learn a basis.

结论CT气-碘双对比造影有助于肩关节损伤的诊断，并为肩关节损伤的法医学鉴定提供重要的影像学依据。

However, in the process of the indirect mercantile agency, especially whether the agent shall take the joint and several liability, in my opinion, to bring the joint and several liability into indirect mercantile agency system should be restricted.

而对于商业间接代理过程中，尤其是代理人是否完全负连带责任，笔者认为将连带责任引入商业间接代理制度之中应加以限制。

Make facial fatigue, eat, speak cause of temporomandibular joint and local myalgia, mouth opening when the joint will of noise, which will burden a child thinking, affecting the quality of life.

磨牙使面部过度疲劳，吃饭、说话时会引起下颌关节和局部肌肉酸痛，张口时下颌关节还会发出响声，这会使孩子有思想负担，影响生活质量。

Methods: 12 fresh frozen shank-foot specimens from young adults were observed. The tibia was fixed rigidly. The talus and navicular were marked. We exerted different load on the forefoot for keeping it in different motion patterns and measured the three-dimensional coordinates of the marked points on these bones. The relative 3D motion range of the talonavicular joint was calculated. The characteristics of the talonavicular joint and the forefoot and their relationship were analyzed.

采用12例新鲜青壮年小腿足标本，牢固地固定胫骨，标记距骨和足舟骨，分别对足前部加载不同的负荷，使前足处于特定的不同运动状态，用三维数字化仪测量标记点的三维坐标值，计算距舟关节的相对三维运动值，分析距舟关节和前足的运动范围及两者间的关系。

So it's necessary to attribute joint negligent crime to joint crime.

然而传统的共同犯罪理论越来越难以适应社会的需求。

In response to repetitive strain and inflammation, the synovial l-z joints can fill with fluid and distend, resulting in pain from stretching the joint capsule.71 Distension of the articular recesses can also compress the exiting nerve root in the neural foramen or spinal canal, especially when the foramen is already narrowed by joint hypertrophy and/or osteophytes.

反复的应力与炎症反应，可使滑膜l-z关节充满滑液并扩张，导致关节囊收到牵拉产生疼痛。关节囊隐窝的扩张可以压迫神经孔出的神经根出口或压迫椎管内脊髓，尤其当由于关节肥大和/或骨赘形成已经存在椎间孔狭窄时发生率更高。

Article 47 The persons in charge of the trade union of the joint venture company has the right to attend as nonvoting members and to report the opinions and demands of staff and workers to meetings of the board of directors held to discuss issues such as development plans, production and managing activities of the joint venture company.

第四十七条合营公司工会负责人有权列席有关讨论合营公司的发展规划、生产经营活动等问题的董事会会议，反映职工的意见和要求。

ABSTRACT In this dissertation, fault-tolerance of redundant manipulators is thoroughly investigated. First, inherent relationship between the dexterity and fault-tolerance of single-redundancy manipulator is discussed. Both the manipulability and the relative manipulability are utilized for measuring the kinematic fault-tolerance of the manipulator with one joint failure. Furthermore, the relative manipulability is used for measuring dexterity loss resulted by one joint failure, and the relationship between the fault-tolerance measurement and null space vector of Jacobian matrix is established.

本文对冗余自由度机器人的答错性问题进行了深入的分析和迭付：首先研究了单冗余度机器人运动学灵活性与容错性之间的内在关系，提出以故障构形的可操作度和相对可操作度来度量机器人的运动学容错性，用相对可操作度来度量关节故障给机器人操作灵巧性造成的损失，并建立了容错性度量指标与Jacobian矩阵零空间向量之间的关系。

Furthermore, open of segment joints, stretch of connected bolts and contact stress distribution on joint faces are the main points which decide whether or not the joint is safe.

同时，接缝的张开、连接螺栓以及接缝处接头面的受力状态是判断接头是否安全的主要依据。

A plane joint model was built in this thesis. By using it, not only M-θ curve of joints but also open of segment joints, stretch of connected bolts and contact stress distribution on joint faces can be obtained.

为此，本文建立了平面型纵缝接头的力学模型，根据该模型除能得到衬砌二维计算所需的接头M-θ曲线外，还能分析接头面的受力状态并得到接缝的张开值、螺栓受力。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐