查询词典 joe rocker

The red dot on the "rocker arm" dip switch is depressed down to turn on (1) the switch position.

这个红点就"摇臂" dip开关是压抑下来，把对（ 1 ）开关的位置。

The downward-moving side of the rocker arm pushes on the valve stem to open the valve.

摇臂向下移动的那一边推动气门杆以打开气门。

lectures on the spot machining industry is undergoing structural changes. The design and improvement of technology and equipment have become a necessary condition for the existence and development of enterprises. Process Equipment Design and direct impact on improving the quality and performance valve rocker arm shaft bearings.

现货机械加工行业发生着党课的结构性变化，工艺工装的设计与改良已成为企业生存和发展的必要条件，工艺工装的设计与改良直接影响着气门摇臂轴支座的质量与性能。

This paper introduces the valve rocker arm shaft bearing on the role and process analysis, followed by rough determine the size, then the process specification free verse.

本文首先介绍了气门摇臂轴支座的作用和工艺分析，其次确定毛坯尺寸，然后进行了工艺规程自由诗。

With an adjustable crank pin to control the length of stroke.As the bull gear rotates,the rocker arm is

惠氏机构的电机转动重载齿轮，驱动一个带有可调整销钉的曲柄以便控制进、回程的长度。

The "EPG" and "ETG" parallel gripper lines utilize a double acting piston and rocker arm design.

在"电子节目指南"和"ETG的"爪平行线利用了双动活塞和摇臂的设计。

Especially in recent years for the development and production of the Korean company Hyosung GF series rocker arm bushings products and the success of products, Hyosung Corporation has been designated as China's only a few manufacturers of sentinel procurement cooperation.

特别是近年来为韩国晓星公司开发生产GF等系列摇臂产品和轴套类产品的成功，已被晓星公司定为中国仅有的几家定点采购合作厂家之一。

At present, there are over 100 species series, camshaft, single-class production capacity will reach 800,000 sets of production over domestic production camshaft and rocker arm valve with matching, and most of all the manufacturers.

目前共有100多个品种系列，凸轮轴生产能力达到年单班产量80万套以上，是国内生产凸轮轴、气门摇臂相配套、品种最全的生产厂家之一。

The effects of technical parameters of laser surface alloying processing on the qualities of the alloyed layer of rocker arm used in motor were investigated with orthogonal test,and the factors and their levels were analyzed.

采用正交试验，对激光表面合金化工艺参数进行了优化，分析了各工艺参数对气门摇臂合金化层质量的影响。

Wantong Wenzhou Pump Co., Ltd., is a professional engaged in the production of fuel injector, tappet, up tight, and the damping plate, rocker arm, such as auto parts companies, in particular fuel injector technology, our company through years of research and exploration A number of technical personnel through the above efforts do not try and experiment, and finally mastered the production of fuel injector technology and methods.

温州市万通泵业有限公司，是一家专业从事生产喷油嘴，挺杆，涨紧器，阻尼板，摇臂等汽车配件的公司，尤其是喷油嘴技术，我公司经过多年的研究和探讨，通过多位技术人员的不段努力尝试和实验，终于掌握了制作喷油嘴的技术和方法。

We are in a good position to meet your requirements.

我们完全可以满足你方的需求。

We are all pervade d with a sense of disaster.

我们普遍有大祸降临的感觉。