查询词典 joe rocker

This design firstly fixed ondesign scheme and selected basic components, and besides, developedthe reliability analysis of transmission system. The design ofMG300/701-WD Shearer's cutting unit. It is made up of a gearbox andmoderate breeze gear wheel transmission that the MG300/701-WD typemining machine cuts the cutting department, Cut the electricalmachinery of cutting department and put to fix up horizontally inthe rocker arm, The power that the motor outputs leans on a roundof transmission of department of gear wheel and planet round viathe tertiary straight tooth, Urge the cylinder to rotate finally.

本文首先确定了设计方案和选择了基本部件并开展了传动系统的可靠性分析，MG300/701-WD型采煤机截割部主要是由一个减速箱和四级齿轮传动组成，截割部电机放在摇臂内横向布置，电动机输出的动力经由三级直齿圆拄齿轮和行星轮系的传动，最后驱动滚筒旋转。

Several essential problems about the mechanism, such as the relations between cam angles and geometric parameters, the allowable values of some angular parameters, the equations of cam prole and the return motion of rocker AC, are solved.

关于这种机构的几个基本问题得到解决，如凸轮角度和几何参数的关系，一些角参数的允许值，凸轮的轮廓线和摇杆的回行运动的方程。

The old prospector had stayed alone up in the mountains so long that he'd gone off his rocker.

这位年老的探矿者，独自一个人在山上呆了很久，他已发疯了。

Oh I wish I was a punk rocker with flowers in my hair,.......

我都没自信想那会不会是给我的话。。。。。。。。。

On the basis of drawing on the technology and experiences of tower assembling and erection for 500kV and 750kV transmission lines in China, such methods suitable to the tower assembling for UHV transmission line as inside suspension pole with outside pulling wires, ground rocker pole and tower crane are adopted and applied in UHVAC test and pilot project, pursuantly the task of tower assembling and erection in this project is completed, from this a lot of practical experiences are achieved and can be available for reference to subsequent engineering and construction..

文章在借鉴我国500 kV和750 kV架空输电线路组塔施工技术和经验的基础上，提出了内悬浮外拉线抱杆组塔、落地摇臂抱杆组塔、塔式起重机组塔等适合于特高压线路铁塔组立的方法。该方法已在特高压交流试验示范工程中得到应用，为后续工程建设提供了技术储备。

An IEC mains inlet and rocker switch look after the power, while the input is doubled up on both balanced XLRs and quarter-inch jacks to provide a choice of connection methods.

驱动低音的是40W的功放，而高音单元则为30W的功放所驱动，整体包装重为5kg.24dB/octave分频点设在3.2kHz， 60Hz-22kHz的系统反应，可是没有最大SPL图。

This is controled by the rocker arm.

这是由摇臂。

The rocker arm and the connecting rod are important parts of the loader's working device.

摇臂和连杆是装载机工作装置的重要部分，对它们的设计一般用传统的类比法和试凑法。

Then the finite element analysis methodare introduced to check the strength of the rocker arm and the connecting rod.

所求得的载荷在有限元分析中将被加载到相应的模型位置。

Process Equipment Design and direct impact on improving the quality and performance valve rocker arm shaft bearings.

现货机械加工行业发生着党课的结构性变化，工艺工装的设计与改良已成为企业生存和发展的必要条件，工艺工装的设计与改良直接影响着气门摇臂轴支座的质量与性能。

We are in a good position to meet your requirements.

我们完全可以满足你方的需求。

We are all pervade d with a sense of disaster.

我们普遍有大祸降临的感觉。