查询词典 isothermally

The time interval for which the antioxidant stabilizer system present in a test specimen inhibits oxidation is measured while the specimen is held isothermally at a specified temperature in a stream of high-purity oxygen, so that the OIT of material sample can be determined.

通过将加有抗氧化稳定剂的试样置于特定温度的高纯氧气流下，测量从通氧至氧化反应之间的时间间隔，来确定材料的OIT。

The free energy for PPS crystals formed during the crystallization isothermally from melt decreased by incorporating POI in to the matrix.

POI是PPS的增塑剂，成核剂和扩链剂，与POI共混使得PPS结晶速率增加，平衡熔点上升，表面折叠自由能降低。

Objective:To develope an injectable, bioresorbable bone substitute that can immediately harden isothermally in situ for meeting developments in minimally invasive techniques for orthopedic surgery.

目的 为研制一种适应整形外科微创技术发展的一种可注射、可吸收、无产热、原位立即变硬的骨替代材料。

The microstructure, strength-toughness and fatigue properties of an ultrahigh strength steel 40CrMnSiMoVA have been investigated. The so-called eta-bainite,composed of thin rareined austenite films within or between the bainitic ferrite laths was found in the steel after isothermally quenched at 300℃ for 1h.

本文研究了飞机起落架用超高强度40CrMnSiMoVA钢的显微组织、强韧性和疲劳性能，结果表明，该钢经300℃等温1h淬火可获得由贝氏体铁素体板条与条间或条内的残余奥氏体薄膜所组成的准贝民体组织。

An ultra-high strength, weldable, low alloy steel with excellent cryogenic temperature toughness in the base plate and in the heat affected zone when welded, having a tensile strength greater than 830 MPa (120 ksi) and a micro-laminate microstructure comprising austenite film layers and fine-grained martensite/lower bainite laths, is prepared by heating a steel slab comprising iron and specified weight percentages of some or all of the additives carbon, manganese, nickel, nitrogen, copper, chromium, molybdenum, silicon, niobium, vanadium, titanium, aluminum, and boron; reducing the slab to form plate in one or more passes in a temperature range in which austenite recrystallizes; finish rolling the plate in one or more passes in a temperature range below the austenite recrystallization temperature and above the Ar3 transformation temperature; quenching the finish rolled plate to a suitable Quench Stop Temperature; stopping the quenching; and either, for a period of time, holding the plate substantially isothermally at the QST or slow-cooling the plate before air cooling, or simply air cooling the plate to ambient temperature.

在基体板以及焊接时的热影响区处的低温韧性优异的超高强度、可焊接、低合金钢具有高于830MPa（120ksi）的抗拉强度，并且具有包含奥氏体薄膜层和细晶粒的马氏体／下贝氏体板条的显微层状组织，所述钢的制备过程为：加热含有铁以及特定重量百分比的添加元素的钢坯，所述添加元素为碳，锰，镍，氮，铜，铬，钼，硅，铌，钒，钛，铝，以及硼中的一些或全部；在奥氏体可发生再结晶的温度范围内，采用一个或多个道次，将所述钢坯轧制成板材；在低于奥氏体再结晶温度但高于Ar 3 转变点的温度下，采用一个或多个道次对所述板材进行终轧；将所述终轧板材淬火至一适当淬火终止温度；停止所述淬火；或者在空冷前在QST点基本等温保持所述板材一段时间，或者对所述板材进行缓慢冷却，或者只是简单地将所述板材空冷至室温。

LiNi0.95Mg0.05O2 could be formed with I(003)/I(104) ratio 1～1.1, R-factor I(006+I(102)/I(101) ratio 0.67～0.94, and (108)/(110) splitted peak, c/a ratio 4.914～4.925, in R3m space group under the conditions of 210~280 MPa pelletized powder, heating rate 2℃/min to precalcined temperature 600℃ for 9～15h,crushed and repelletized, heated till 600℃ in 5℃/min, then switched to 1℃/min till 750℃ isothermally for 15～20h all in oxygen flow.

发现以210～280 MPa对试样压片，在氧气气氛下经2℃/min升温速率升温至600℃，预烧9～15h后，再粉碎、压片以5℃/min升温至600℃之后以1℃/min升温至750℃恒温15~20h，可得I(003)/I(104)峰比值1~1.1，R-factor I(006+I(102)/I(101)峰比值0.67~0.94，并且有(108)与(110)的分裂峰，同时c/a比值4.914~4.925，属于R3m空间群的锂镍镁氧化合物。

PTT-rich blends (Wpbt≤30%) isothermally crystallize toform ring-banded spherulite.

PTT/PBT共混物的相形态与组成密切相关。

On the other hand, if Ti foil is too thick, the interfacial reaction between liquid Cu-Ti alloy and Al〓O〓 ceramic can proceed sufficiently, due to the widening of the liquid phase region. This results in a too thick reaction layer, which also reduces the joint strength. Further more, in this situation, not all of the liquid alloy is isothermally solidified, similar to the case of brazing, the heatresistant of joint can't be improved.

相反，Ti箔过厚，一方面由于液相区宽度增大，连接过程中始终为Cu-Ti液体合金与陶瓷反应，导致形成过厚的反应层，降低接头强度；另一方而，由于连接后液相区未能完全等温凝固，与活性钎焊相类似，接头耐热性也难以得到提高。

This paper introduces automatic production line for isothermal normalization with residual heat from forged steel parts and installed computer distributed control system,(which can be used for heating up gear billet and normalizing isothermally for the second time)developed by our company,which form a complete set with AMP70 hot former made in Switzerland.

介绍了我厂研制的与引进瑞士AMP70热镦机配套的具有计算机集散式控制系统的锻坯余热等温正火自动生产线(可兼作二次加热齿坯等温正火)。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。