查询词典 isothermal parameter curve

The preparation of indirubin(1)-phospholipid complex was optimized using binding ratio of 1 and phospholipid as evaluation parameter.

以靛玉红(1)与磷脂的复合率为指标优化了1磷脂复合物的制备工艺。

The fluctuations and phase transition properties of light intensity are investigated in Chapter 3 for a two-mode inhomogeneously broadened laser taking account of full saturation effects with multiplicative noise stemmed from disturbances in laser gain parameter.

第3章讨论了非均匀展宽双模激光中当乘法噪声由增益参数涨落引起并计入全饱和效应时，光强的涨落和相变特性。

However the workpiece tends to deform inhomogeneously and causes residual stress with the intuitive large numbers of the delta parameter in the skin-pass process.

以冷间表面精抽改善圆棒与等边型材的真直度和同心度等几何精度时，由於精抽制程的塑性变形区Δ参数相当大，工件容易发生变形不均，造成残留应力，影响后续产品使用之精度。

The performace of material was tested by DSC,XRD,SEM,EIS and charge-discharge cycles . The influences of various synthesized condition , sintering time and the amount of F were studied and correlative technics parameter to improve performance of material were optimized. DSC shows that three endotherimc peaks and one large exothermic peak are observed in the temperature range 150-400℃, which is because of the removal of water,the decomposition of the organic constituents and the formation of spinel. Only the citrate precursor is sintered at least 450℃, the crystallinity of spinel phase could be formed intactly.

通过DSC、XRD、SEM、EIS和充放电循环等手段对材料进行性能测试，比较了不同合成温度、烧结时间和不同掺杂元素量等条件对材料性能的影响，优选出提高材料性能的相关工艺参数， DSC表明，采用溶胶-凝胶-络合法制备的前驱体在150-400℃中有三个小的吸热峰和一个大的放热峰，这是前驱体中的水分、柠酸酸及其盐和醋酸及其盐在蒸发及分解，柠檬酸前驱体至少需在450℃以上才可能形成完整的尖晶石材料。

The parameter of beam positions at HLS 200 MeV LINAC is very important to injection efficiency.A new strip-line beam position monitor system was designed recently,which is not interceptive to beam,qualified in precision and easy to digitalize the results.

合肥光源(Hefei Light Source，HLS)200 MeV直线加速器的束流横向位置是一个重要的运行参数，直接决定注入的效率，为此新开发了一种非拦截型、高精度、易于将测量结果数字化的条带电极束流位置测量系统(beam position monitor， BPM)，该系统由条带电极和信号处理系统组成。

The second is pursuant to the same value as the solubility parameter or similar to the principle of mutual ureplasm, forecasting two solvents or ink and substrate intersolubility.

其二是依据溶解度参数值相同或相近的可以互溶的原则，预测两种溶剂或油墨与承印物的互溶性。

" Described in this article modei-method " one is pursuant to the same or are similar to the solubility parameter can be miscible the judgment resin in solvent or mixture is dissolved and inks and substrate intersolubility.

本文所述的&两维制墨方法&其一是依据溶解度参数相同或相近可以互溶的原则，对判断树脂在溶剂或混合溶剂中是否溶解及油墨与承印物的互溶性。

The interweaving information indicates the branch amounts of parameter convolution interweaver and the bytes amount in each memory unit.

交织信息指示交织器的参数卷积交织器的支路数目和每个存贮单元的字节数。

At last,this paper analyzed the influence of the inversive receiver to the chracteristic of the clutter and the ratio of signal power and the noise power ,discussed the effective detection of target signal in correlated clutter,and then put forward a new method naming multi-periods shift accumulation for detecting moving target when not knowing the exact movement parameter.

最后，本文分析了倒置接收对目标回波信噪比及杂波特性的影响，讨论了在相关杂波区对回波信号有效检测的方法。针对如何在弹目相对运动参数未知的条件下对高速运动目标进行积累检测这一问题，提出了一种多周期移位积累的新方法。

The parameter estimation problem to the invertible vector moving average model essentially is a matrix spectral factorization problem.

中文摘要：可逆的向量滑动平均模型参数估计问题本质上是一个矩阵谱分解问题。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。