查询词典 isochronous

In Chapter 3, we study the boundedness of solutions and the existence of invariant tori for two kinds of isochronous systems.

在第三章中，我们研究了两类等时系统解的有界性和不变环面的存在性。

Study on the solution of brachistochrone and the effect of friction;2. Based on physics,it was proved concisely that the cycloid is both brachistochrone and isochronous pendulum.

介绍旋轮线的主要性质及其在日常生活与物理中的一些实例，并结合物理学知识对其最速降线与等时性进行简洁的证明。

It is important and difficult for isochronous correlation datum of fluvial facies stratum in exploration and development of petroleum, while high resolving power of sequence stratigraphy based on the datum plane cycle is an additional feasible technical method for it.

河流相地层的等时对比一直是油气勘探开发的重点和难点，而基于基准面旋回的高分辨率层序地层学则为此增添了行之有效的技术手段。

A center's service area of a geographic network is broadly applied in practical life. In traditional method, it is expressed by an isochronous area or an equidistance area.

地理网络的中心服务范围在实际生活中应用广泛，传统方法一般用等时区或等距区表示。

From the composite section, it can be found that some fossils'range zones are too short. Maybe it is caused by the fossils not preserved properly or the samples not collected comprehensively. Most fossils'first occurrence data are later than the ages which are defined by the MIDK4 composite section. It is probably caused by the Foraminifer zones in Tethyan- Himalaya which are not isochronous with other areas. It can also be recognized that there are two major extinction and revival events at the boundary of Cenomanian/Turonian and the boundary of Coniacian/ Santonian. They are coincident with the two Ocean Anoxic Events and can be considered as the typical response by creatures.

在复合剖面上可以发现：一些化石的延限非常短，这可能是由于化石保存不完整或者样品采集不全造成的；大部分化石的首现面年龄值都要晚于MIDK4数据库复合剖面给出的年龄值，这可能是由于特提斯喜马拉雅带与全球其他地区的有孔虫化石带不等时造成的；同时，可以在复合剖面上识别出在Cenomanian/Turonian界线附近和Coniacian/Santonian界线附近存在两次大规模的生物灭绝和复苏事件，这正好与两次大洋缺氧事件发生的时间一致，可以作为缺氧事件的生物标志。

With increasing loading, the reduction degrees of average correlative coefficients of linear fitting functions of isochronous stress axial strain curve and isochronous stress-radial strain curve are 0.97% and 0.67% respectively, which indicates the linear correlation decreases commonly.

随加载应力水平的提高，应力－轴向应变等时曲线和应力－径向应变等时曲线线性拟合函数的平均相关系数下降幅度分别为0.97%和0.67%，线性相关性普遍降低。

The average correlative coefficients of linear regression function for isochronous stress- axial strain curve are 3.92% higher than that of average correlative coefficients of linear regression function for isochronous stress- radial strain curve, so nonlinear creep property of the fine sandstone specimen in axial direction is correspondingly weaker than that in radial direction.

应力－轴向应变等时曲线线性回归函数的平均相关系数高出应力－径向应变等时曲线线性回归函数的平均相关系数3.92%，因此其轴向非线性蠕变特性相对于径向非线性蠕变特性更弱。

Based on formers criteria of isochronous centers for centers, we analyze parameter conditions of isochronous centers.

在此基础上，还在前人获得的多项式Liénard方程的等时中心判据的基础上，进一步分析了等时中心的参数条件。

At last, the isochronous center of infinity of a class of quintic systems is studied and all conditions of center and isochronous center are obtained for infinity of this system, which is the first time for the research on the isochronous center of infinity.

最后，研究了一类实平面五次系统的无穷远点的等时中心，给出了系统无穷远点为中心和等时中心的全部条件。这是迄今对无穷远点等时中心进行的首次研究。

In the last chapter, by introducing the isochronous center of real systems into complex planar and defining complex center and complex isochronous center, a concise linear recursion formula for period constants is given, necessary and sufficient conditions of complex isochronous center (the Time-Angle Difference Theorem) proved, conditions of real systems with linearizable center and saddle treated unitedly and the isochronous center conditions discussed fully for a class of real planar cubic systems.

在第七章，通过把实系统等时中心引入复平面研究，定义了复中心和复等时中心，给出了等时中心周期常数计算的简明的线性递推公式，证明了等时中心判定的充分必要条件，统一地处理了实系统具有可线性化的中心和鞍点条件，并对一类实平面三次系统的等时中心条件进行了完整研究。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐