查询词典 irradiation

In this season,the bauhinia flowers was bright,irradiation in the branches of a purple,with the gray cement road,the mottled khaki-colored walls of the old house and the black blue of stone walls rendering each other mutually shining,like a watercolor.

这个季节，紫荆花开的灿烂，铺陈在树枝上的一片紫色，与水泥路的灰色、老房子斑驳外墙的土色、石头围墙的黑青色互相渲染，如同一幅水彩画。

In t his season,the b auhiniaflowers was bright , irradiation in the branches of a purple, with the gray cement road , t he mottled khaki-colored walls of the oldhouse and the black blue of stone walls rendering each other mutually shining ,like a watercolor. Listening from my friends

这个季节，紫荆花开的灿烂，铺陈在树枝上的一片紫色，与水泥路的灰色、老房子斑驳外墙的土色、石头围墙的黑青色互相渲染，如同一幅水彩画。

The capture efficiency is usually about 50% by ordinary design method in the electron linac for irradiation processing.

一般电子辐照加速器的俘获效率在50％左右，一半的电子都损失在加速管内。

The control system of the lOMeV linac for Irradiation processing is a Distributed Control System.

本控制系统采用分布式网络控制，由多个子系统构成。硬件采用SIEMENS PLC和监控计算机。

With the dose of 7.04 mC/cm2, ODT/Au will become a more strengthened structure and then form a negative resist in the correlation with cross-linking from alkyl matrix, partial breakdown of S-Au bonding and surface adsorption by air-borne species. Thus, it can obtain a gold pattern via gold-etching process. Besides, as a result of massive breakdown of alkyl matrix and S-Au bonding from ODT/Au under irradiation with doses of 64.06 and 128.13 mC/cm2, ODT SAMs would form a loose-packed structure on the gold substrate. The ODT/Au becomes less resistive for gold-etching and a positive gold pattern would form after gold-etching.

结果发现：以50 eV 低能量电子在照射剂量7.04 mC/cm2微影并曝露於大气后，受到来自於ODT/Au碳链间的交联、部分的S-Au键结破坏以及照射后立即曝露大气所吸附於表面的碳氧化物种的共同影响下，ODT SAMa於Au膜基材上将形成更紧密复杂的结构而作为负型阻剂，经后续湿式蚀刻15分钟后将显影出来Au的负型图案；当提升照射剂量至64.06及128.13 mC/cm2后，由於ODT/Au上碳链及S-Au键结的大量破坏，将使ODT/Au结构不能稳固且紧密地排列於Au膜基材上，显影时Au蚀刻液将容易穿过ODT SAMs抵达S/Au界面而移除Au，而形成正型图案。

While under visible light irradiation, Ag,Pt,Pd and Rh exist as Ag~0, PtCl_4, PdO and Rh0 respectively, which results in that the photocatalytic activity of the M/TiO_(2-x)N_x depends on the generation and transfer pathway of photogenerated electron in M/TiO_(2-x)N_x photocatalyst.

而在可见光下，Ag，Pt，Pd和Rh分别以Ag~0，PtCl_4，PdO和Rh~0的形式存在，M/TiO_(2-x)N_x光催化剂的活性取决于光生电子的激发方式和其转移途径。

3Ultrastructural observation of changes of Mφ with transmission electron microscopy.Results The above mentioned indices of irradiated groups were higher than those of non-irradiated groupP Conclusions The He-Ne laser irradiation in appropriate dosages may activate immunocytes and enhance the body immunity.

结果 各激光穴位照射组小鼠腹腔巨噬细胞对白色念珠菌的吞噬率、吞噬指数及NSE的各项参数值与对照组比较，差异均有非常显著意义（P 结论用适当剂量的He-Ne激光照射小鼠神阙穴能活化其巨噬细胞，从而提高机体免疫功能。

According to the atmospheric window,transmission property of infrared irradiation in atmosphere and the impact of the most appropriate temperature corresponding to the optional infrared band on the controlling of the cooperative target's temperature,8～14 μm was identified as the radiation band of the cooperative target.

根据大气窗口、红外辐射在大气中的传输特性和待选波段对应的最佳辐射温度对合作目标温度控制的影响，确定了8～14μm波段为合作目标对应的辐射波段。

Under the same conditions, irradiation with ultraviolet lamp at a power of 1.5 W/m 3 and radiation intensity of 90 μW/cm 2 for 30 min produced the germicidal efficacy similar to that produced by 2 g/m 3 Chinese drug candle fumigation disinfectant.

在相同条件下，以功率 1。 5W/m3、辐射强度 90μW/cm2 的紫外线灯照射 30min，其杀菌效果与 2g/m3 中药蜡烛烟熏消毒剂相似。

Compared with the annealing treatment, laser irradiation is a fast and effective way to tailor CMR manganites for industrial applications.

根据对传统退火效应的分析和理论计算，认为激光辐照导致的表面微结构的变化以及薄膜的氧含量和均匀性的提高对LBMO薄膜的磁电性能的改善与优化密切相关。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。