查询词典 inverting input

This is the inverting input of the brownout detect comparator.

这是掉电检测比较器反相输入端。

If the inverting input is made slightly more positive, the output will become more negative, this is why the name "inverting" is given to this input.

11 ，如果反转的投入是稍微更积极的，输出将变得更加消极的，这就是为什么命名为"反转"是给这个投入。

Being connected to the inverting input of the op amp, it should be at the same potential as the amplifier's non-inverting input.

由于该点与运放反相端直接相连，所以该点电位与运放同相端相等。

All voltage values, unless otherwise noted, are with respect to the midpoint between VCC + and VCC C. Differential voltages are at the noninverting input terminal with respect to the inverting input terminal.

所有的电压值，除非另有说明，关于之间的VCC +和VCC电压差分正处于中点是关于反相输入端同相输入端。

As a DC/DC basic structure is adopted, the operational amplifier leads the non inverting input end voltage of the error amplifier to follow the input voltage linearly, thus realizing the linear following relation between the output voltage and the input voltage.

由于采用DC/DC的基础结构，增加运算放大器使误差放大器的同相输入端电压与输入电压线性跟随，从而实现输出电压与输入电压的线性跟随关系。

When a noise signal is present, a pilot signal and noise signal passing through a capacitor are applied to the inverting input port of the subtracter via a second MOS transistor to cancel the noise signal contained in the composite input signal.

当噪声信号时，一个试验信号与噪声信号通过电容通过应用通过一个晶体管第二马鞍山到减法反相输入端口，取消噪声信号的复合输入信号中。

In high-impedance current-input inverting configurations, where a length of shielded wire is used to guard the lead from the current source to the amplifier's inverting input, the guard should either be driven by a buffer at the same potential as the non-inverting input, or be tied directly to the non-inverting input, with a second outer shield connected to the signal's reference point.

如果将运放接成反相放大器的形式，并且在信号源与运放反相端之间用一段带有屏蔽层的导线来充当的防护罩，那么对防护罩的处理有两种选择：要么用一个缓冲跟随器来驱动，跟随器输出端与运放同相端电位相等，而且除跟随器外，防护罩不与其他点接触；要么将防护罩直接接到运放的同相端，然后在其外面加一个屏蔽层，并且将屏蔽层连接到信号的参考电位。

The invention discloses a DC/DC circuit, comprising a PWM controller, a current amplifier, a peak current comparator, an error amplifier, a main switch, a synchronous switch and also an operational amplifier. The non inverting input end of the operational amplifier is used for coupling with input voltage or voltage reference, or used for coupling with the input voltage and the voltage reference; the inverting input end of the operational amplifier is used for coupling with the voltage reference or ground, and the output end thereof is connected with the non inverting input end of the error amplifier.

本发明公开了一种DC/DC电路，包括PWM控制器、电流放大器、峰值电流比较器、误差放大器、主开关和同步开关；还增设运算放大器，其同相输入端用于与输入电压或基准电压耦合，或用于同时与输入电压和基准电压耦合；其反相输入端用于与基准电压或地耦合，其输出端与所述误差放大器的同相输入端连接。

S1 is then changed to position 1. The voltage stored on C1 is inserted between the output and inverting input of the amplifier and the output of the amplifier changes by VIN to maintain the amplifier input at the input offset voltage. The output then changes from (VOS + IbiasR2) to (VIN + IbiasR2) as S1 is changed from position 2 to position 1. Amplifier bias current is supplied through R2 from the output of the amplifier or from C2 when S1 is in position 2 and position 1 respectively. R3 serves to reduce the offset at the amplifier output if the amplifier must have maximum linear range or if it is desired to DC couple the amplifier.

接着 S1 拨到位置 1，使 C1 的电压加在放大器的输出端和反相输入端之间，(由于电容端电压不能突变，所以)输出端的电压将产生大小等于 VIN 的变化，使放大器输入端维持输入失调电压，即当开关 S1 从位置 2 拨到位置 1 时，输出端电压将从(VOS + IbiasR2)变为(VIN + IbiasR2)。S1 处于位置 2 时，放大器的偏置电流是由输出端经电阻 R2 提供的，当 S1 转向位置 1 时则由 C2 提供。R3 的作用是降低输出失调电压，如果要求放大器具有最大的线性范围，或者采用直流耦合，就应该使用该电容。

An inverting AMPLIFIER configuration with a false ground reference at the non-inverting input prevents these errors by holding the input common-mode voltage constant.

反相放大器在同相输入端进行虚地的配置，可防止这些由共模电压引入的误差恒定。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。