查询词典 intravenous
- 与 intravenous 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Intravenous injection of dextran iron hydroxide may correct the lack of iron in hemodialysis patients, improve the iron utilization and the effect of rHuEPO, thus ameliorate renal anemia.
静脉补铁优于口服补铁,静脉注射右旋糖酐氢氧化铁能有效纠正血透患者的铁缺乏,提高铁的利用率及基因重组红细胞生成素的治疗效果,改善了贫血状态。
-
Objective To explore the application effect of ketamine combined with propofol in the intravenous anesthesia on children.
目的 探讨氯胺酮复合丙泊酚在小儿静脉麻醉中的应用效果。
-
Ketamine , the phencyclidine derivative described in 1965 , is an intravenous anesthetic with a variety of applications .
氯胺酮,苯环衍生的描述于1965年,是一个与静脉麻醉的各种应用。
-
Objective To investigate the effect of intravenous low dose ketamine pretreatment on propofol.
目的探讨预注小剂量氯胺酮对异丙酚麻醉效果的影响。
-
The discomfort associated with administration can be avoided by infusion into large-bore veins as well as pretreatment with intravenous lidocaine.
选择较粗的静脉和静脉预给利多卡因可以消除注射时的不适。
-
Two large-bore (14-16-gauge) intravenous lines are placed.
建立两个大孔径(14-16号)静脉通道。
-
A minimum of 2 large-caliber intravenous catheters should be established.
至少需建立两个大口径静脉导管通道?
-
A minimum of 2 large-caliber intravenous catheters should be established. Establishment of upper extremity peripheral IV access is preferred.
可以采用最小2号静脉导管行静脉置管术,插管的部位首选上肢的外周静脉。
-
These results can be used for production of intravenous and intramuscular preparations, liniments and suspensions
眼药水准备生产,可治疗预防网膜血栓和次生溢血,也可作为角膜炎和角膜穿孔伤的再生促进剂
-
After intravenous injection of liposomal Gd-DTPA, the contrast of hepatic metastases was better than that before enhanced.
采用标准SE序列的T1WI作为兔肝转移瘤模型增强前扫描序列,组织对比度较好,图像质量好。
- 相关中文对照歌词
- Intravenous Agnostic
- Give Me Life
- Basic Cable
- Public Property
- The Dragon Of Judah
- Supernatural
- Let It Die
- Gunz Yo
- Supernatural
- Detroit Swing 66
- 推荐网络例句
-
Based on the relationship and the phenomenon model, an improved model of MR damper has been presented in this paper.
摘 要:本文在实验数据的基础上建立了磁流变阻尼器输出力与不同常电流控制量的关系,对现有的 p模型进行了改进。
-
I don't think our founding fathers were very fuckable.
我认为我们的开国元老没什么吸引力
-
In chapter 3, an optimum method of milling parameter based on orthogonal cutting finite element model is proposed.
第三章提出了基于正交切削加工有限元模型的铣削参数优化方法。