查询词典 interpolation polynomial

The optimum solution is gotten by Joint limitation avoidance, then the joints trajectory can be obtained by interpolation calculation of three order polynomial, finally PTP trajectory in joint coordinate system is planned.

过去，对控制系统进行仿真，只能建立一个数学模型，仿真的结果是一堆抽象的数据。

First, orthogonal circle operator was modeled in terms of Zernike orthogonal complex moment; the one-to-one mapping between the edge point and the parameters of the circle was established by the algorithm. Then, quadratic polynomial interpolation was adopted to further locate the edge points in the gradient direction.

首先根据Zernike正交复数矩建立圆物体边缘点与边缘参数之间的映射关系，并提取边缘点；然后利用二次多项式插值在梯度方向上对提取出的边缘点进行进一步定位；最后利用最小二乘法拟合插值后的边缘点，得到亚像素精度的圆参数。

The errors and area limits caused by the lunar curvature were avoided in this model established under the Selenocentric Orthogonal Coordinate System, the accidental errors of exterior line elements were reduced by orbit fitting and interpolation, the polynomial orders of systematic errors in satellite orbits were decreased with their expression in the flying coordinate system moving and rotating with satellites, and the reliability of exterior orientation solution was enhanced under the condition of sparse and low accuracy control points by appending constraint of orbit and attitude parameters.

该模型通过在月心直角坐标系进行影像空中三角测量来消除月球曲率引起的误差和测图范围限制，通过轨道形状的拟合与插值来减小摄影时刻轨道位置的偶然误差，在飞行坐标系中建立轨道修正模型来减少定向参数的数目，对轨道和姿态增加约束条件来提高月面控制点数目稀少及精度低条件下外方位解算的精度与可靠性。

Application of polynomial approximation based single peak spectral lines interpolation algorithm in interharmonic analysis.

基于多项式逼近的单峰谱线插值算法在间谐波分析中的应用。

Combined with the condition of the study site and test data characteristic, it did quadratic polynomial transform, bilinear interpolation resampling, and gained matched images.

结合本文试验区地形情况和实验数据的特点，对所选影像数据按二次多项式变换、双线性内插方法进行重采样，实现影像间精配准。

ABSTRACT This paper summarizes our researches on two key techniques in curve and surface modeling-the geometric approximation techniques and the geometric interpolation techniques. The former includes three types of geometric approximation techniques: Hybrid polynomial approximation to rational curves and surfaces, offset curves and surfaces approximation, interval Bézier curves and surfaces approximation. The latter includes a series of algorithms for shape blending modeling: the MSI algorithm for shape blending between space polylines or trees, the MSI algorithm for shape blending between triangular meshes, and skeleton-based shape blending algorithms using triangular decomposition and star-shape decomposition.

本文是作者对曲线曲面造型中两类核心技术几何逼近技术和几何插值技术的研究成果的总结，其中前者包括有理曲线曲面的Hybrid多项式逼近、等距曲线曲面逼近和区间曲线曲面逼近等三类几何逼近方法；后者包括用于形状混合造型的几何插值方法的一系列算法：空间多边形形状混合的MSI插值算法、三角网格形状混合的MSI插值算法、树的形状混合的MSI插值算法以及基于骨架树形状混合的三角剖分算法和星形剖分算法。

Used squared eancroid method for CCD image subdivided locating,discussed on squared cancroid method,and compared it with traditional centroid method, Gauss curvefitting method , and polynomial interpolation method.

介绍了激光三角测距传感器的基本工作原理和激光光斑成像噪声处理的主要方法，将平方加权质心法应用于激光在CCD中成像的细分定位，并与传统质心法、多项式插值法和高斯曲线拟合法进行了较为系统的比较；通过实验表明，平方加权质心法是一种较为理想的细分定位方法，不仅简单、易于实现，而且具有更高的定位精度以及抗噪声的能力。

Used squared cancroid method for CCD image subdivided locating, discussed on squared cancroid method.and compared it with traditional centroid method, Gauss curvefitting method, and polynomial interpolation method.

本文介绍了激光三角测距传感器的基本工作原理和激光光斑成像噪声处理的主要方法，将平方加权质心法应用于激光在CCD中成像的细分定位，并与传统质心法、多项式插值法和高斯曲线拟合法进行了较为系统的比较。

Report : Programming Environment : Newton MATLAB7 K polynomial interpolation procedures to achieve Romberg of Quadrature program Gaussian out PCA Elimination of the program.

详细说明：计算方法实验报告：编程环境：MATLAB7.0 牛顿K次插值多项式的程序实现龙贝格求积公式的程序实现高斯列主元消去法的程序实现。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐