查询词典 integrating factor

The wind forcing is the most important factor(80%) for generating the JB cyclonic gyre In addition the wind forcing drives the Liman Current and damos the East Korean warm Current in the Winter , and generates the UTB eddies al ong the Japan Nearshore Branch in all seasons .

风强迫是产生日本海盆气旋性式涡旋的最重要的因素(80％)。此外，风强迫在冬季驱动了Liman Cold Current流，抑制了东朝鲜暖流，并且在全年都产生UTB涡旋和沿着日本近岸分支的一些涡旋。

Using limekiln gas which was exhausted during theprocess of producing calcium carbide to reaction with water glass, did single-factor experiments and discussed the effect of factors on carbonization process, ratio of production and performance of product ,such as temperature and time of reaction, the density of raw material and carbon dioxide etc.

利用电石生产排放的含二氧化碳的废气—石灰窑气和水玻璃进行碳化反应，进行了单因素试验，探讨反应温度、反应时间、原料配比及二氧化碳浓度等因素对碳化过程、产率及产品性能的影响。

With application of plastic limit analysis method using finite element method, stability of high loess slope is analyzed and solved by using linear programming method in this paper. Safety factor and stress fields and velocity fields of slope can be obtained.

本论文采用有限元塑性极限分析法对黄土高边坡进行稳定分析，并运用线性规划的方法对稳定问题进行求解，可以得到边坡的稳定安全系数和边坡的应力场及速度场。

It is very practical for geotechnical engineering design.Fundamentals of the limit state finite element method are discussed in this paper,such as the definition of safety factor and the selection of yield criteria.Through a series of case studies,the applicability of the proposed method is demonstrated.

本文探讨了极限分析有限元法的一些基本原理，包括安全系数的定义、岩土体整体失稳的判据、屈服准则的选用等，并将该方法应用于边坡、地基、隧道稳定性计算，算例表明了此法的可行性，拓宽了该方法的应用范围

Then,calculates the slope\'s stabilization by the limit equilibrium method and the limit element method,evaluates some factors that influence the slope\'s safety factor .

然后利用极限平衡法和有限元法对滑坡进行稳定分析，并对滑坡的安全系数影响因素进行评价，为治理提供依据。

With the development of computers and computing technology,the limit state finite element method has been put forward.With strength reduction or load increase,the stability safety factor and failure surface can be obtained directly at limit state.

随着计算机技术的发展，极限分析有限元法应运而生，它能通过强度降低或者荷载增加直接算得岩土工程的安全系数和滑动面，十分贴近工程设计。

A new method of slope stability, limit equilibrium finite element method based on Dijkstra algorithm, was established by applying the improved Dijkstra algorithm which was an algorithm to seek the shortest path in graph theory to search for the minimum safety factor of slopes and the position of most dangerous sliding plane.

通过引入图论中解决最短路问题的Dijkstra算法到搜索边坡最危险滑动面及其安全系数中去，对Dijkstra算法作了一定的改进，建立了一种新的边坡稳定性分析方法―基于Dijkstra算法的极限平衡有限元方法。

To the best of our knowledge, for the efficiency limit of DOEs, published papers either consider only one single factor or consider both phase only and phase quantization together. This is relatively insufficient for the real DOEs, because most of them are phase-only and spatially quantized.

由所知的文献显示，对於绕射元件的绕射效率上限，过去的论文只单独考虑某一因素，或只同时考虑纯相位及相位量化两个因素，或所提出的绕射效率上限过於保守，这对於实际的绕射元件而言，是相当不够的，因它们多数是纯相位且已空间量化的。

Firstly, several kinds of schemes were proposed according to the design demand. The best scheme was chosen after analyzing and comparing the schemes. The robot's structure was designed with Pro/Engineer and AutoCAD software. Secondly, the kinematics analysis conducted, coordinate transformation matrix using D-H method was set up, and the kinematics equation direct solution and inverse solution was deduced. The manipulative interface about the kinematics equation direct solution and inverse solution was completed with VC++ and the velocity Jacobian of displacement matrix was constructed using differential transform method. In the process of the trajectory planning based on robot's kinematics analysis, I propone a method by which we can get middle nodal point with normalizing factor in order to simplify our searching for these middle nodal points. In addition, I give these middle nodal points with actual physics signification. For eliminating contradiction between real-time and accuracy, I bring forward separately limit of error and reversal interpolation method. For decreasing calculation quantity, we resort to tri-spline interpolation in the articulation space.We analyse the work range of the robot by resorting to graphic means.

首先，作者针对机器人的设计要求提出了多个方案，对其进行分析比较后，选择其中最优的方案后用Pro/Engineer和AutoCAD软件进行了机器人模型结构设计；其次，进行了运动学分析，用D-H方法建立了坐标变换矩阵，推算了运动方程的正、逆解，运用VC++制作了正、逆运动学求解的求解界面；并且用微分变换法推导了速度雅可比矩阵；在基于机器人的运动学的轨迹规划中，通过在操作空间的规划，提出了归一化因子来求解中间结点，通过它可以使求解中间结点变得更简单，并且赋予这些中间结点实际的物理含义，对于规划中精确性和实时性的矛盾，提出了以误差极限法和反向插值法来解决的方法；为了减少规划过程中计算量，在关节空间进行三次样条插值；然后借助图解法进行工作空间分析，作出了实际工作空间的轴剖图。

This value is used to compare the strength of materials, but a safety factor is applied when making design calculations, to bring the working stress well below the limit of proportionality.

此值被用来比较材料的强度，但是当设计计算时，要用一个安全系数，使工作应力低于比例限制。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。