查询词典 integrating element

Two special cases are discussed: flow due to a constant pressure gradient and flow due to a periodic one; In chapter 4, on the basis of the method of fractional element proposed by Schiessel et al and of the generalized fractional element networks proposed by Xu and Tan and by the use of discretization method for solving the inverse Laplace transform, we obtain the creep compliance of Zener and Poynting-Thomson models which are composed of the generalized fractional element networks.

并讨论了如下两种特殊情形：常压力梯度下的流动和周期性压力梯度下的流动；第四章在Schiessel等提出的分数阶单元法和徐明瑜等提出的广义分数阶单元网络的基础上，应用离散求逆Laplace变换的方法，给出并讨论了广义分数阶单元网络Zener和Poynting-Thomson模型的蠕变柔量。

In 1999, Nicholson further introduced the concept of strong clean rings as follows: A ring R is said to be strongly clean if every element of R is the sum of an idempotent element and an invertible element that commute with each other.

W.K.Nicholson进一步引入了强clean 环的定义：一个环R 被称为强clean环，如果R中的任意一个元素均可以表示成一个幂等元和一个单位和的形式，并且幂等元和单位可换。

When a put call is made for a new element (and assuming that the max limit is reached) the element with least number of hits, the Less Frequently Used element, is evicted.

当为一个新对象调用put（假定已经到了最大对象的限制），最少命中的对象，最少使用的对象被移出。

Two nonlinear macro elements including beam-column element and wall element are established, fiber model is used for section analysis of element.

采用两种非线性宏观单元―梁柱单元和墙单元，单元截面分析采用纤维模型。

If wanted to cube each element in the matrix, just use the element-by-element cubing.

如果想每个立方体中的矩阵元，只需要使用元素的元素刺。

Prepared by the three-dimensional finite element beam element of the element stiffness matrix calculation program, the 6-DOF nodes.

用matlab编写的，有限元三维梁单元的单元刚度矩阵计算程序，各节点6个自由度。

At first step, the processor before the deformable body contact the end face of cone die cavity regarded as an extrusion process. The minification of core boss's cross-section regarded as compressibility of direct extrusion, which acted as definition factor when construct the Direct Extrusion Model element. Another step, the model element of flat punch extrusion on wedge piece process was constructed when propose the process of deformable body overflow die corner. In this way the spherical end face of blank looked as cone end face one, t he approximate treatment is one of originality innovation in this paper. At last, the two elements have been connected and constructed the model element of cone boss part's deformation in the open die forging.

对于锥形凸台成形的第一个特征时段，即坯料和锥形凸台型腔的端面接触之前的变形过程，本文将凸台的截面缩小率转换成挤压成形的压缩率并以此为界定，建立了不同截面缩小率时的锥形模正挤压的模型单元；对于锥形凸台成形的第二特征时段即锥形模的角部充满过程，在详细考察锥形型腔端面对变形过程影响的基础上，将变形体的球形端面近似成锥面建立了平冲头挤压楔形体的模型单元；最后将前述两种模型单元有机连结，构建了开式模锻中整个锥形凸台成形过程的定量描述。

A rational procedure is presented to solve finite element problem mixing nonlinear and elastoplastic materials. To avoid numerical problem, the incremental finite element analysis of geometrically altered structures is adopted, and a corresponding automatic finite element mesh strategy is proposed for simulating construction process of excavation.

本文采用变结构有限元分析方法，建立了一种可以灵活模拟基坑工程各种施工工况的有限元网格方法，该方法克服了现有的一些网格方法无法模拟加支撑、加锚杆或拆支撑的缺点，以及不便于计算机自动生成有限元网格的不足，可以更全面、准确地模拟施工过程，大大方便了有限元前处理工作。

The effect of the elastic-plastic matrix of friction soil with nonrelevant flow rule on the numerical convergence of finite element method is analyzed in this paper; and the effect of elastic modular, poisson ratio and earth pressure coefficient on numerical results are studied in this paper. At the same time, the hybrid element with a mixture of displacement and stress variables and the conventional element with solely displacement variable are compared when used in geomaterials.

在ABAQUS有限元分析软件的基础上，本文研究了服从非关联流动法则摩擦性土体的弹塑性矩阵对有限元数值算法的影响，并研究了弹性模量、泊松比以及地基土压、力系数对数值计算结果的影响，同时探讨了数值分析过程中常规位移元与杂交元在岩土工程中的应用。

In this paper, draw the idea of beam unit, the bias along the vertical box is divided into a number of oblique beam. On the basis of analysis of the displacement, through positive and oblique coordinate transformation relations, and directly built on the oblique coordinate system to describe the methods of displacement unit space. With potential energy principle is derived in oblique beam element stiffness matrix and the establishment of the finite element formulation. The preparation process of the finite element analysis is used to verify the structure of bias.

本文吸取梁段单元的思想，将斜交箱梁沿纵向划分为若干斜梁段，在位移分析的基础上，通过正、斜交坐标转换关系，直接建立在斜交坐标系内描述单元空间位移的方法，用势能驻值原理推导斜梁单元刚度矩阵并建立其有限单元列式，利用编制的有限元程序进行斜交结构的分析。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。