查询词典 intake valve

A water baffle is vertically arranged in the vessel, which divides the vessel into an intake region and an exhalant region; because the lower part of the water baffle and the lower part of the vessel are provided with a gap, the intake region is communicated with the exhalant region; an inlet and an outlet are respectively arranged on the upper part of the intake region and the upper part of the exhalant region; a drain is arranged at the lower part of the vessel, on which a drain valve is arranged.

一种茶浴炉炉外储垢排垢器为一密闭容器，容器内竖向装有阻水板，将容器分隔成进水区和出水区，阻水板与容器底部有一定间隙使进水区和出水区相通，进水区和出水区上部设有进水口和出水口，容器最低部设有排污口，其上装有排污阀。

With electronic control, this system can have a function of variable valve timing by rotating hydraulically driven intake and exhaust valve sleeves slightly.

通过电子控制技术，对本机构的液压阀套的角度微调，就能达到可变气门正时。

This action could open an inlet valve for an intake stroke, or open an exhaust valve for an exhaust stroke.

这过程能使进气门在进气行程打开，或者排气门在排气行程打开。

Vertical sliding column valve is the use of a column in the shoulder of the slide valve body axial movement, so that the air intake on or off of.

纵向滑柱阀是利用一个有台肩的滑柱在阀体内轴向移动，从而使各气口接通或关断的。

Secondly, the flow characteristic of the intake system of pre-mixed spark ignition gas engine was studied on the vacuum pump. The discharge coefficient models of the air valve, the gas valve and the subsystem of the mixer and throttle were modeled. Their working flow characteristics were analyzed. And the dynamic model of the intake system was identified.

其次，在真空泵流量实验台上完成了预混点燃式气体燃料发动机进气系统的流量特性研究，建立了空气阀、燃气阀及"混合器+节气门"子系统的流量系数模型并分析了其工作流量特性；建立了发动机外围进气系统的动态模型。

Intake efficiency is the most fundamental and important parameter for engine performance, yet the open and close timing as well as the lift depth of the intake valves are determined by the contour curve of the camshaft, that means the valve timing and lift depth are constant and fixed.

进气效率，是引擎最基本也是最重要的性能参数之一。而进汽门的开启时间与关闭时间以及扬程的大小是经由凸轮轴的轮廓曲线所决定，亦表示汽门正时与扬程是固定不变的。

Through the analysis of different cross section flow field in cylinder of two-valve and four-valve diesel engine, the following conclusion can be obtained: The formation of intake swirl of two-valve diesel engine mainly is effected by an intense air flow ring zone near the radius from valve axis to cylinder axis, as the flow progresses down through the cylinder, the ring zone air flow expends to both side and finally forms an unified rigid rotating swirl motion.

2号缸盖的螺旋进气道产生的绕自身气门轴线的动量矩比1号缸盖的大，且切向气道的径向速度在前峰面上的数值比1号缸盖的速度数值大很多，因此，两进气道组合后的动量矩损失也大，所以虽然2号缸盖的两个进气道单独的涡流比都高于1号缸盖的两个进气道，但组合后的合成涡流比却是基本相同的。

Other Northstar firsts on the XLR include four-cam continuously variable valve timing; electronically controlled, hydraulically actuated intake and exhaust cam phasers on all four camshafts for extra control; electronic throttle control; low restriction intake and exhaust manifolds and cylinder head ports; close coupled catalytic converters mounted directly adjacent to the exhaust manifolds; and a new air induction system, redesigned for enhanced capacity and noise attenuation.

Other北极星上首创的XLR包括四凸轮连续可变气门正时，电子控制，液压驱动进排气上的额外控制所有四个凸轮轴凸轮相位调节；电子节气门控制；低，限制进气和排气管和缸盖港口；紧密耦合催化转化器直接安装毗邻的排气管，以及一个新的空气感应系统，增强能力和噪声衰减重新设计。

Kinematic and dynamic calculations are carried out, and the features of intake and outtake valve train are got. Especially, the area of fullness ratio of the valve lift curve, cam to tappet contact stress, lubrication coefficient and the features of valve seating are analyzed.

在此基础上分析了配气机构进排气部分的工作特性，着重从气门升程曲线的丰满系数、凸轮与平面挺柱间接触应力，凸轮与平面挺柱间润滑效果以及气门落座特性等方面进行了分析。

To accommodate the engine's large valves and enable more direct intake port flow, the intake-side rocker arms are offset 6 mm between the valve tip and the push rod.

为了适应发动机的大型阀门，并让更多的直接进气口流量，进气端摇臂被抵消6阀之间的尖端和推杆毫米。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。