查询词典 input signal

In high-impedance current-input inverting configurations, where a length of shielded wire is used to guard the lead from the current source to the amplifier's inverting input, the guard should either be driven by a buffer at the same potential as the non-inverting input, or be tied directly to the non-inverting input, with a second outer shield connected to the signal's reference point.

如果将运放接成反相放大器的形式，并且在信号源与运放反相端之间用一段带有屏蔽层的导线来充当的防护罩，那么对防护罩的处理有两种选择：要么用一个缓冲跟随器来驱动，跟随器输出端与运放同相端电位相等，而且除跟随器外，防护罩不与其他点接触；要么将防护罩直接接到运放的同相端，然后在其外面加一个屏蔽层，并且将屏蔽层连接到信号的参考电位。

Thus, the output will always be driven by a single transistor, either P- channel or N-channel. Since they are as closely matched as possible, the output resistance of the gate will always be the same, and signal behavior is therefore more predictable. Fig. 3.4 CMOS NAND gate One of the main problems with CMOS gates is their speed. They cannot operate very quickly, because of their inherent input capacitance. B-series devices help to overcome these 24 Lesson 3 CMOS Logic Circuit 25 limitations to some extent, by providing uniform output current, and by switching output states more rapidly, even if the input signals are changing more slowly. Note that we haven't gone into all of the details of CMOS gate construction here. For example, to avoid damage caused by static electricity, different manufacturers developed a number of input protection circuits to prevent input voltages from becoming too high. [3] However, these protection circuits don't affect the logical behavior of the gates, so we won't go into the details here. New Words and Phrases 1. CMOS abbr.

略语互补金属氧化物半导体(complementary metallic oxide semiconductor)逻辑，逻辑学，逻辑性，推理方法补充的，补足的，互补的电池供电的门电路，逻辑门，闸门，控制栅，大门，通道，门口，入口伏特，环骑，闪避基础的，基本的，主要的基本原则，基本原理增强型金属氧化物半导体场效应晶体管(metallic oxide semiconductor field effect transistor)反相器，反用换流器，变极器来源，水源，消息来源，原始资料，发起者源，源极排水沟，消耗，排水漏极排出，喝干，耗尽排水，流干，耗尽相同的，相配的，匹配的匹配有效地，有力地，事实上，实际上无限的东西无穷大无穷的，无限的，无数的，极大的接地的正向偏置的，正偏的或非 25 2。

If the input password is correct, then from P3.0 output unblanking signal, if the input password is not correct, then from P3.1 output password rub-out signal, if continual three times inputs the password is wrong, then from P3.2 output alarm, once the output alarm, after must wait for relieves reports to the police only then unlocks.

如果输入密码正确，则从P3.0输出开锁信号，如果输入密码不正确，则从P3.1输出密码错误信号，如果连续三次输入的密码均是错的，则从P3.2输出报警信号，一旦输出报警信号，就必须等待解除报警后方可重新开锁

So we designed a adaptive synchronizing controller based on hereinbefore hardware environment: first a small magnitude reference signal r is outputted to system through the signal card (to ensure that the vibrating system works in a linear state), and this signal is sent to the moving coil of vibrator through the power amplifier, so vibration is produced through electromagnetic induction. Secondly the vibration signal can feedback to the data acquiring card in the servo system through the acceleration sensor on the Vibroseis reactor M〓 and the base-plate M〓, then the computer can get the current vibrating state y〓 of the coil of vibrator according to the feedback information from the data acquiring card, and give a real time comparing between the current state y〓 and the reference output y〓 of the set-in reference model with current reference input being r , then regulates the correlative controlling parameters according to the error e〓=y〓-y〓 till y〓→y〓, finally normal signal sweeping begins with a certain phase fixed. Meanwhile a synchronization signal for seismic signal record is sent to seismograph from synchronization signal outputting component in the Vibroseis system to perform the controlling process of synchronization of sweeping phases.

为此，我们基于以上的硬件环境设计了一个自适应同步控制器：首先通过信号发生卡对系统输出小幅度的参考信号r(从而保证振动系统工作处于线性状态)，信号通过前置放大器、功率放大器等送到激震器动圈，并通过电磁感应产生振动，振动信号通过可控震源激震器反应块M〓和基板M〓上的加速度传感器反馈给伺服系统中的数据采集卡，工控计算机根据采集卡的反馈信息，获取当前激震器动圈的振动状态y〓，并实时地将该状态与内置的参考模型在当前参考输入r下的参考输出y〓进行辨识，再将两者输出误差e〓＝y〓-y〓对系统的有关控制参数进行调整，直至y〓→y〓，最后在经过某一固定的相位后，开始信号的正常扫描过程，与此同时，由可控震源系统的同步信号输出部件向地震仪送出一地震信号记录同步信号，进而完成扫描相位同步控制过程。

Only half of Nokia 6030- There are four signal input wires instead of two signal input wires in the second generation, which makes more brand cars available by easy connection without any teardown and adding any other parts.

只有一半诺基亚6030有四个输入信号而非电线电线两个信号输入的第二代这使更多品牌轿车方面没有任何可轻易拆卸、添加任何其他部分。

First use of sensors to convert the weight of voltage signal, and then voltage signal amplification input A / D converter, followed by A / D converter tool analog signals into digital signals, the digital signal will be sent to the microcontroller, through the process of Signal processing, and weighing function, and then the weight and keyboard input price multiply calculated lump sum, and the weight and price with LCD display.

首先用传感器把重量转换成电压信号，再将电压信号放大输入A/D转换，利用A/D转换工具将模拟信号转化为数字信号，将得到的数字信号传送至单片机，通过程序对信号进行处理，实现称重功能，然后将重量与键盘输入单价相乘计算出总价，并将重量和价格用LCD显示出来。

A method of processing a series of input audio signals representing a series of virtual audio sound sources placed at predetermined positions around a listener to produce a reduced set of audio output signals for playback over speaker devices placed around a listener, the method comprising the steps of: for each of the input audio signals and for each of the audio output signals: convolving the input audio signals with an initial head portion of a corresponding impulse response mapping substantially the initial sound and early reflections for an impulse response of a corresponding virtual audio source to a corresponding speaker device so as to form a series of initial responses; for each of the input audio signals and for each of the audio output signals: forming a combined mix from the audio input signals; and forming a combined convolution tail from the tails of the corresponding impulse responses; convolving the combined mix with the combined convolution tail to form a combined tail response;for each of the audio output signals: combining a corresponding series of initial responses and a corresponding combined tail response to form the audio output signal.

提供了一种处理一系列输入音频信号的方法，所述输入音频信号代表放置在收听者周围预定位置的一系列虚拟的音频声源，该方法可以产生一组精简的用于在收听者周围的扬声器装置上进行播放的音频输出信号，该方法包括以下步骤：对每个输入音频信号和每个输出音频信号进行以下步骤：用相应的脉冲响应最初的头部对输入音频信号进行卷积以形成一系列初始响应，其中的脉冲响应充分映射了相应的虚拟声源到相应的扬声器装置的脉冲响应的初始声音和早期反射；对每个输入音频信号和每个输出音频信号进行以下步骤：形成音频输入信号的混音；并根据对应脉冲响应的多个尾部形成复合的卷积尾；用复合的卷积尾对音频信号的混音进行卷积以形成复合尾部响应；对每个音频输入信号进行以下步骤：把相应系列的初始响应与相应的复合尾部响应进行复合以形成音频输出信号。

At first, setting up the arith relation between the signal input and the signal output of the generalized multi-carrier system of the Discrete Fourier Test spread-spectrum; then setting equilibria parameters of the frequency field equilibria subcarrier of the generalized multi-carrier system of the DFT spread-spectrum according to channel frequency response, channel noise variance and equilibria method; then calculating average power of useful signal, interferential average power between signals as well as noise variance of the generalized multi-carrier system receiving terminal of the DFT spread-spectrum according to the arith relation as well as the frequency field equilibria parameter, and recomputing available signal information noise ratio, so as to calculate the available signal information noise ratio of the generalized multi-carrier transmission system accurately, the method for estimating the available signal information noise ratio can be used for link self-adapting transmission solution of the generalized multi-carrier system based on Discrete Fourier Test spread-spectrum and radio material management.

一种DFT扩频的广义多载波系统的SINR估计方法，其通过首先建立所述离散傅立叶变换扩频的广义多载波传输系统的信号输入输出之间的数学关系，然后根据信道频率响应、信道噪声方差和均衡方法，设定所述DFT扩频的广义多载波传输系统的频域均衡子载波的均衡系数，再根据所述数学关系及所述频域均衡系数分别计算所述DFT扩频的广义多载波传输系统接收端有用信号的平均功率、信号间干扰的平均功率以及噪声方差，再计算有效信干噪比，如此以实现对广义多载波传输系统的有效信干噪比的准确计算，该有效信干噪比估计方法可用于基于离散傅立叶变换扩频的广义多载波传输系统的链路自适应传输方案和无线资源管理方面。

TDA4864 Pinout: 8- to 32-bit and 16- to 32-bit word packing options Programmable wait state options: 2 to 31 CCLK Digital audio interface includes six serial ports, two pre- cision clock generators, an input data port, three programmable timers and a signal routing unit Serial ports provide: Six dual data line serial ports that operate at up to 50 Mbits/s for a 200 MHz core on each data line each has a clock, frame sync, and two data lines that can be configured as either a receiver or transmitter pair Left-justified sample pair and I2S support, programmable direction for up to 24 simultaneous receive or transmit channels using two I2S compatible stereo devices per serial port TDM support for telecommunications interfaces including 128 TDM channel support for telephony interfaces such as H.100/H.110 Up to 12 TDM stream support, each with 128 channels per frame Companding selection on a per channel basis in TDM mode Input data port provides an additional input path to the DSP core configurable as either eight channels of I2S or serial data or as seven channels plus a single 20-bit wide syn- chronous parallel data acquisition port Supports receive audio channel data in I2S, left-justified sample pair, or right-justified mode Signal routing unit provides configurable and flexible connections between all DAI components, six serial ports, an input data port, two precision clock generators, three timers, 10 interrupts, six flag inputs, six flag outputs, and 20 SRU I/O pins Serial peripheral interface Master or slave serial boot through SPI Full-duplex operation Master-slave mode multimaster support Open drain outputs Programmable baud rates, clock polarities, and phases 3 Muxed Flag/IRQ lines 1 Muxed Flag/Timer expired line ROM based security features: JTAG access to memory permitted with a 64-bit key Protected memory regions that can be assigned to limit access under program control to sensitive code PLL has a wide variety of software and hardware multi- plier/divider ratios JTAG background telemetry for enhanced emulation features IEEE 1149.1 JTAG standard test access port and on-chip emulation Dual voltage: 3.3 V I/O, 1.2 V core Available in 136-ball BGA and 144-lead LQFP packages Lead free packages are also available

TDA4864引脚说明： 8 - 32位和16 - 32位字包装选择可编程等待状态的选择：2至31个CCLK数字音频接口包括6个串行端口，两个前643时钟发生器，输入数据端口， 3可编程定时器和一个信号路由单元串行端口提供：六双串口数据线，在高达50 Mbps的操作/为200兆赫的每个数据行每个人都有一个时钟，帧同步的核心秒，和两个数据可以作为任何一个接收器或发射器对左对齐和I2S样本对支持，最多可同时接收或传送24个频道，每使用两个系列的I2S兼容立体声设备配置可编程方向线；港口的TDM通信接口，包括支持128个电话接口的TDM的渠道，如H.100/H.110支持多达12个的TDM流的支持下，每帧128个频道每个压缩扩展每通道的基础上选择在TDM模式输入数据端口提供了一个额外的输入路径的DSP核心配置为I2S或串行数据或7加一个20位宽的SYN -异步的并行数据采集接口通道或8通道；支持接收通道I2S音频数据，左对齐样本对，或右对齐模式信号路由单元组件之间提供所有戴配置和灵活的连接，6个串行端口，一个输入数据端口，两个精密时钟发生器，3个定时器，10个中断，六旗投入，产出6个旗，20曼谷南南区域股的I / O管脚串行外设接口的硕士或奴隶通过SPI串行启动全双工运作主从模式多主机支持开漏输出可编程波特率，时钟极性和第三期合并调制旗/ IRQ线路1合并调制旗/定时器过期线光盘的防伪特征：JTAG的访问与64位受保护的关键允许内存内存可分配给程序访问控制的限制下对敏感地区有一个代码锁相环/分比率背景遥测的JTAG仿真功能增强的IEEE 1149.1 JTAG标准测试访问端口软件和硬件多钳各种各样和片上仿真双电压：3.3六/输出，可在1.2 V核心136球BGA封装和144引脚LQFP封装无铅封装，也可

A device (ESF1) for spectral shaping of a discrete value transmission signal in a radio transmitter comprises one input (E1) for receiving an in phase component of the transmission signal and a further input (E2) for receiving a quadrature component of the transmission signal.

一种用于在无线发射机内对数值离散的发射信号进行频谱整形的装置(ESF1)，它具有一个用于接收所述发射信号的同相分量的第一输入端(E1)和一个用于接收所述发射信号的正交分量的第二输入端(E2)。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。