查询词典 inlet

A Caret inlet was studied by testing. Basic aerodynamic characteristics of the inlet at supersonic speed are presented.

对一种Caret进气道进行了试验研究，给出了该型进气道超音速基本气动特性。

The annular sealing member and inlet are provided with means to secure said sealing member to said inlet to prevent axial movement therebetween, said second sealing means engaging the outer curved surface of the tubular member whereby sealing engagement may be effected between the sealing member and the tubular member over a plurality of relative axial positions therebetween.

所述的第二密封装置与管形件的外曲面接合，借此实现密封件和管形件之间在多个相对轴向位置上的密封连接。

The influences of the inlet solution flow rate, the inlet solution temperature, the absorption pressure and the colling condition on heat and mass transfer of absorption process have been discussed.

在此基础上，设计、研制、安装并调试了竖板及矩形通道降膜吸收试验台本体；确定测量方法，选取测量装置并对测量系统不确定度进行了分析。

By flue gas of 2000m〓/h, some normal wastes (seawater, fly ash of power plant, basic waste water, etc) and lime are used on the research of dry, semi-dry, and wet FGD and its corresponding pressure and temperature decrease on stuffing tower, the effect of Ca/S ratio, inlet SO2 concentration, inlet flue gas temperature, and L/G ratio on desulfuration efficiency is analyzed, the instrument of dehumidify was studied by experiment and appropriate instrument of dehumidify was chosen.

在浙大热能所大约相当于1吨／小时出力的锅炉的尾部烟道上的多功能传热除尘脱硫一体化试验研究装置上，利用海水、电厂灰、碱性废水和石灰开展了半工业性的干法、半干法、湿法烟气脱硫研究，分析了Ca／S比、进口SO〓浓度、进口烟温、喷水量等因素对脱硫效率的影响，并探讨了湿法烟气脱硫中的烟温问题，对湿法烟气脱硫反应塔的阻力特性和除湿装置进行了试验研究，选取了合适的除湿元件。

One method of applying an etchant through the descender is to connect an ozone generator to an inlet port of the assembled fluid ejector and supply ozone (e.g., at a 2% or greater concentration in oxygen gas or in a mixture of oxygen and nitrogen) to the descender and the inner surface 450 through the inlet port.

一种通过该下睁部施加蚀刻剂的方法是将臭氧发生器连接到该装配的流体喷射器的入口，并且通过该入口将臭氧(例如，以氧气中或氧和氮的混合物中2％或更大的浓度)提供到该下降部和内表面450。

The diverter may also be used to alternately divert flow from either of the side run-inlet ports to the branch center-inlet port.

这种分流阀也可以用来将两个侧面进口的流体转向到分支中心进口端口。

In order to increase the efficiency, pumps were improved, eject pump had two inlets, each was located on one side of pump, and the inlet of centrifugal pump was used as one Enteromorpha prolifera inlet.

为了进一步提高装置的工作效率，在原有设备的基础上，对离心泵和喷射泵均进行改进，喷射泵改为双吸口，位于泵体两侧，同时离心泵的入水口也作为浒苔吸口使用，并给出喷射泵主要设计参数。

The composition of the device comprises a substrate and a cover plate. A cross-form groove is disposed on the base material of the substrate; a disperse phase fluid inlet pipe and a fluid outlet pipe are respectively inlaid in the groove to form a coaxial sleeve structure; a continuous phase fluid inlet pipe is embedded in a groove on the two sides and connected with the coaxial sleeve; and the cover plate is hermitically attached to the upper surface of the substrate and seals the groove.

其组成包括基片和盖片：所述基片的基材上开有一个十字型凹槽；分散相流体入口管和流体出口管分别嵌入到凹槽内形成同轴套管结构；连续相流体入口管嵌入到两侧的凹槽内与所述同轴套管相连；所述盖片紧密贴合在所述基片的上表面上将所述凹槽进行密封。

Although this lowest cooling temperature is higher than that achieved by using a double-inlet valve, the cooling power obtained by the refrigerator with an inertance tube is higher than with a double-inlet valve, which demonstrates the excellence of inertance tube.

虽然最低制冷温度高于双向进气型脉管制冷机的制冷温度，但是当制冷温度在75K以上时，惯性管型脉管制冷机的制冷量大于双向进气型脉管制冷机的制冷量，从而体现了惯性管的优越性。

Based on summing-up of the existent design method of two-dimensional and three-dimensional inlets,a parametric design method of two-dimensional hypersonic inlet was established by analyzing the restrictiveness and sensitivity of the geometric parameter of the inlet.

在归纳二维进气道和三维侧压式进气道设计方法的基础上，通过参数制约关系分析和参数敏感性分析，提出了二维进气道的参数化设计方法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。