查询词典 inlet

This process put the anaerobic tank and secondary settlings and the recirculation of nitrified wastewater and the recirculation of sludge and Orbal oxidation ditch inyto together at the basement of Orbal oxidation ditch and the secondary settlings which the inlet and outlet were both circumjacent. This process had many advantages such as the small taking-up area and lower investment and consuming of energy and strong adaptability to raw influent.

介绍了一种新型一体化Orbal氧化沟，该池以Orbal氧化沟和周进周出辐流二沉池为基础，将厌氧池、二沉池、硝化液回流、污泥回流系统与Orbal氧化沟组合为一体，具有占地面积小、投资省、能耗低、原水适应能力强、运行管理更方便的突出优点。

It will be more clinically significant that VSD is classified into perimembranous, conoventricular, atrioventricular canal or inlet, muscular and subpulmonary artery or conical types.

将室间隔缺损分为膜周型、圆锥隔心室型、房室通道型、肺动脉瓣下或圆锥隔型和肌部型更具有临床意义。

A numerical simulation was conducted for a fixed-geometry two-dimensional mixed-compression supersonic inlet with sweepforward high-light and "X" type missile configuration. The results indicate:(1) The total pressure recovery declines with the rise of the free stream Mach number, while the mass flow ratio rises firstly and then declines when its maximum value is obtained at the design point.

针对一种定几何二元倒置&X&型混压式超声速进气道开展了数值仿真研究，结果表明：随着来流马赫数的增加，进气道总压恢复系数下降，而流量系数却先上升，在设计点达到最大值后下降。

Some types of tankless models are thermostatically controlled; they can vary their output temperature according to the water flow rate and inlet temperature.

有些种类的tankless模式温控；他们可以改变其输出的温度根据水流量和入口温度。

Based on this principle, the mathematical model of an exothermic reactor is established to caculate Exothermic reator length L corresponding to reation temperature T, reation temperature T corresponding to ammonia mole fraction y and the average internal reactor wall temperature Tave corresponding to exergy output Enet and thermal power output Q. The curves of L-T, T-y, Q/Enet –Tave are drawn with the caculated date which can directly reflect the influence of reactor inlet gas temperature and reactant flow rate on ammonia synthesis reaction for the reactor under the conditions of definite design pressure and hydrogen/nitrogen ratio. Furthermore, the design parameters to realize maximum exergy output and thermal output are presented.

文章分析了储能体系的选择，介绍了氨基热化学储能的基本原理，在此基础上建立了放热反应器的数学模型，计算和绘制出了L-T、T-y以及热量和佣输出与反应器内壁平均温度之间的关系曲线，直观地反映了在一定的设计压力和氢氮比条件下，进气温度和进气流率对放热反应的影响，给出了实现佣最优化和热能最优化的操作参数。

At the same advanced angle, the emission quan tities of CO, HC u nder rated speed were greater than those under maximal torque speed; Increasing app ropriately the inlet air...

同一进气动压，标定转速下所生成的CO ，HC要多于最大转矩转速情况；冷却水温对于排放的影响不能孤立考虑，要结合缸内温度同时进行。

Operation Manual, Nitrogen Product Compressor (C1761) Turbocompressor Unit, Gearbox, Coupling, Inlet guide vane, Gascooler

操作手册，氮气产品压缩机（ C1761涡轮压缩机装置，齿轮箱，联轴器，入口导向叶片，气体冷却器

Design principle of guide device for high speed wile lolling mill are introduced, also construction of different types at inlet and outlet part, material, design method, and fixing way with underbed in DANIELI rough, intermediate and flushing high speed wire rolling mill are described.

介绍了高速线材轧机导卫装置的设计原则及达涅利高速线材轧机粗、中、精轧机组不同类型的入口和出口导卫装置的结构、材质、设计方法及与底座的固定方式。

This paper develops a series of study of design, simulations and test on a bar vertex ban inlet uniflow hydrocyclone providing an alternative to the traditional hydrocyclone with the actual situation of its separation mechanism and test research.

本论文结合水力旋流器分离机理及实验研究存在的实际情况，针对区别于常规水力旋流器的新型涡流板入口结构直流式水力旋流器开展了一系列的设计研究和模拟实验，并同返流式水力旋流器进行比较。

Refer to the finned tube separator and the uniflow cyclone separator, the effects of the inlet particle concentration on the separating efficiency and the pressure lose is studied.

针对鳍片管束分离器和下排气旋风分离器，研究了入口颗粒浓度对分离效率及阻力的影响

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。