查询词典 inlet flow

Air inlet filter pressure differential gauge, shipped loose.

空气进气过滤器压差表，散件。

The main research work includes:(1) To analyze the structure of 165F, explain the technical difficulty of indirect injection and the solution way from many aspects include of the shape and arrangement of combustion chamber, organizing of inlet air swirl, selection of injector and so on.

主要研究内容包括：(1)分析165F的结构，从燃烧室的形状与布置、进气涡流的组织、喷油器选择以及诸因素的匹配等方面说明小缸径柴油机直喷化的技术难点以及解决的方法。

The difference are, self-pressrize fuel tanke and the air inlet strainer.

机身和发动机采用MD500D民用型的设计，区别在于加装自密封燃油箱、发动机进气道过滤器。

Moreover, increasing of fuel inlet temperature will lessen the mixing of the fuel and air in primary combustion zone, so the reactants distribution is more uniform and NOx emission is reduced greatly.

提高燃气入口温度，可抑制燃料和空气在主燃烧区的混合，使火焰内反应物的分布更加均匀，抑制了热力NO的生成，从而减少了NOx的排放量。

A sliding vane in between the air inlet and outlet will prevent air flowing from high pressure zone to low pressure zone.

在进气口与排气口之间的一个滑片将阻止空气从高压区流向低压区。

A sliding vane in between the air inlet and outlet will prevent air flowing from high pressure zone to low pressure zone.

在进气口和排气口之间的一个滑片将阻止空气从高压区流向低压区。

The analysis of the inlet is one of the most difficult problems in the analysis of the Radar Cross Section of aircraft.

飞机进气道的电磁散射计算是预估飞机的雷达散射截面的难点问题之一。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

The analysis of leakage causes for flash trough was presented, and the wear layers on inlet tube and the baffle wear plate inside of flash trough were used to increase the wear life of flash trough.

分析了闪蒸槽泄漏的原因，采用在进口接管堆焊耐磨层及筒体上增加耐磨档板的方法对闪蒸槽进行了改造，增加了闪蒸槽的寿命。

It is very important to understand the effect of oil film reformation and rupture boundary condition on the journal bearing performance when journal, bearing block perturbation and inlet oil pressure exist.

由于轴颈、轴承扰动的作用和进油压力的不同，油膜形成和破裂边界也发生相应的变化，因此有必要研究上述变化对轴承性能的影响。

Diabetes is a social disease that affects several million people worldwide.

糖尿病是一个社会性疾病，全世界有数百万人罹患此病。

I'll call you on Friday to see if we can reschedule our luncheon meeting at your convenience.

我星期五会给您打电话在您方便的时候我们重新安排我们的午餐约会。