查询词典 inlet flow

This thesis deals with the axial non symmetry of air flow in the cyclone, with change of single inlet to double inlet .

针对旋风器内气流轴不对称问题，从结构上改单进口为双进口。

After inlet model s three dimensional structural grid was generated, proper numerical scheme and onflow model were choosed, then numerical computation on flow field of inlet was taken, finally the better results were got.

通过建立三维结构化网格模型，选择合适的数值格式与湍流模型，对进气道流场进行数值模拟，得到了合理的结果。

The distance between settled releaser and inlet of raw water is 180 cm, and the range of distance between pensile releaser and inlet of raw water is 60-90 cm. The flow of pensile releaser is 2-3 times as much as settled releaser.

较为合理的布置为：固定式释放器S与原水进水口距离为180 cm，悬挂式释放器P与原水进水口的距离在60～90 cm之间。P与S的流量比控制在2～3之间。

The effects of process parameters, such as the pressure and the temperature of the saturator, the inlet flow rate and inlet solution concentration of the precipitator, on the particle size and particle size distributions were examined.

在自建的超临界辅助雾化过程实验装置上，以红霉素－乙醇－二氧化碳系统为研究对象，分别研究了混合器压力和温度、溶液浓度及进液速率对微粒形态和粒径的影响。

The experiments show that the PS and PSD of particles produced by SAA process can be controlled by adjusting process parameters, and among them, the pressure of the saturator used has the most effect on the PS and PSD, while the temperature of the saturator has the least effect. When using ethanol as solvent, the optimum operating conditions of using SAA process to produce erythromycin micro-particles from erythromycin-ethanol-CO2 system were found as follows. The pressure and temperature of the saturator are 10.5MPa and 70℃, respectively, the inlet flow rate and the concentration of inlet solution of the precipitator are 9 mLmin^(-1) and 15mgmL^(-1), respectively.

实验结果表明：选用乙醇做溶剂可制备出粒径在1~3μm的红霉素超细微粒，大部分微粒形态呈完整的球形；各影响因素对微粒粒径及粒径分布均有不同程度的影响，其中混合器压力对微粒粒径及粒径分布的影响最明显，混合器温度的影响最小，微粒粒径及粒径分布可通过改变操作参数进行控制；在本研究范围内，最优操作条件为混合器压力10.5MPa，混合器温度70℃，溶液浓度15mgmin^(1)，进液速度9mLmin^(1)。

The influences of the inlet solution flow rate, the inlet solution temperature, the absorption pressure and the colling condition on heat and mass transfer of absorption process have been discussed.

在此基础上，设计、研制、安装并调试了竖板及矩形通道降膜吸收试验台本体；确定测量方法，选取测量装置并对测量系统不确定度进行了分析。

The diverter may also be used to alternately divert flow from either of the side run-inlet ports to the branch center-inlet port.

这种分流阀也可以用来将两个侧面进口的流体转向到分支中心进口端口。

To research the ways of relieving inlet unstart phenomenon, the flow of a typical hypersonic 2-D inlet with different suction positions was analyzed in this paper.

对某典型二元高超声速进气道流场进行了二维数值模拟，研究了抽吸位置及抽吸流量对进气道性能的影响。

When a sudden power failure or accident or normal pump stops when the pump stops, the valve inlet water velocity to reduce stress Agency, the valve plate also fall, when its velocity is zero (that is, inlet flow rate is zero Department), large valve plate because of its own gravity and rapidly turn off (time 3s ~ 5s), the majority of water to prevent backflow, when the valve before and after the formation of a water pressure, water stress, on the one hand through the small valve at the bottom of the three slot for pressure relief vent pressure. 4 water stress from the bypass tube into the cavity patch up the control room (this process for the suction pressure chamber that can effectively absorb the energy of water), when water stress on cavity than inferior vena cava, the pressure of water promote the diaphragm down mobile , the current cavity pressure of water being squeezed out all the small valve plate slowly drop back to standby status, the process time to ease closure adjustable (3s ~ 150s), then the valve has been fully closed, watertight.

当突然停电或事故停泵或正常停泵时，阀门进水口处压力水流速降低，大阀板也随之下降，当其流速为零时，大阀板由于自身重力而迅速关闭（时间3s～5s），可防止大部分水倒流，此时阀门前后形成一种水压差，压力水一方面通过小阀板底部的三条泄压槽进行泄压。4）压力水从旁通管进入膜片控制室上腔（此过程为吸压腔，能有效吸收一部分水能量），当上腔压力水大于下腔时，压力水推动膜片往下移动，当下腔压力水全部被挤出来时，小阀板缓缓下降，恢复到待机状态，此过程中缓闭时间可调节（3s～150s），届时阀板已全部关闭，滴水不漏。

Findings-The inner flow field changes quickly according to 1 gas inject velocity; 2 surrounding air temperature and pressure, and 3 position of jet nozzle and air inlet. The aim of this project is to find an optimum position and geometry for gas generator and inlet opening that can provide a high aspiration ratio for the new design inflator.

在一封闭空间中外围空气可藉由进气道吸入其中，空气由进气道被吸入的气体会因著喷场的速、周遭环境的温与压、喷嘴与进气道的几何形及其相对应的装置位置等因素而改变，且受后端气囊在震波冲击下的开启运动而影响。

"Yes, now you can give yourself airs," she said, you have got what you wanted.

"对了，您现在高兴了，"她说道，这是您所期待的。

Then the LORD said to me: Rebel Israel is inwardly more just than traitorous Judah.

上主于是对我说：＂失节的以色列比失信的犹大，更显得正义。