查询词典 injection

The company is headquartered in Hong Kong, factory located in Shenzhen, China, factory covers an area of 50,000 square meters, employs more than 600, with mold manufacturing, injection molding, screen printing, such as fuel injection sector, and self-development of a variety of 28mm-96mm standard electrical transformer shell, rectifiers shell companies and so on ...

本公司总部设在香港，工厂位於中国深圳，工厂占地面积5万余平方米，拥有员工600多名，设有模具制造，注塑成形，喷油丝印等部门，并自我开发28mm-96mm各种电器标准的变压器外壳，整流器外壳等等。。。

IMD is to have good printing decorative molding sheet Add to injection mold, and then resin injection molding sheet in the back so that the resin and sheet to one of Curing technology.

IMD就是将已印刷成型好的装饰片材放入注塑模内，然后将树脂注射在成型片材的背面，使树脂与片材接合成一体固化成型的技术。

A newly developed approach, in which sheet metal forming and plastics injection molding are integrated, was used to manufacture complex components combined with aluminum sheet and polypropylene with the mold of non-flat bottom via plastics injection molding machine.

摘 要：在注塑机上利用非平底凹模制备了形状较复杂的铝板/聚丙烯复合结构件，实现了将金属板料成形、塑料注射成形融为一体的复合成形的新工艺。

My baby was born January 30, when the first injection of hepatitis B vaccine injections, the second needle is injected March 4, and the third a sewing needle injection July 31 of.

我的孩子1月30日出生，当时注射了乙肝疫苗第一针，第二针是3月4日注射的，第三针是7月31日注射的。

Problems such as charge injection and clock feedthrough caused by turning off swithes are analyzed and solved in this design. The optimal switch sequence helps eliminate the nonlinearity caused by the charge injection; the addition of dummy switches to sensitive nodes caused by the clock feedthrough can greatly reduce the coupled charge; and the use of high PSRR folded cascode differential input stage can restrain the interference from the power supply. The circuit performance, therefore, has been greatly improved.

设计中分析并解决了因时钟信号引起的制约开关性能的因素：优化的开关时序消除了电荷注入引起的非线性；时钟馈通敏感节点增加虚拟开关抵消了耦合电荷；高PSRR共源共栅折叠式差分输入结构，有效地抑制了来自电源的干扰，改善了电路的性能。

I have an independent mold factory workshop, blow / injection molding workshop, self-opening mode, sample / material processing all kinds of plastic electrical accessories and plastic blowing / injection plastic products.

我厂拥有独立的模具车间，吹/注塑车间，可自行开模，来样/料加工各种塑料电器配件及塑料吹/注塑料产品。

By studying the processing properties of the self-leveling HM199 room temperature vulcanized sealant for airport runway joint ,it is revealed that the appropriate ratio of the sealant injection depth to the width of joint is 1∶2,but the injection depth should be no less than 6mm,and the recess from pavement to sealant is 3 mm to 7 mm.

阐述了机场跑道接缝密封剂和衬垫材料应具备的性能；通过对自流平型HM199室温硫化密封剂灌注工艺性能的研究，提出密封剂的灌注深度与接缝宽度的最佳比为1∶2，灌注深度最小不低于6 mm，密封剂顶部与道面的距离为3~7 mm。

Result seventy-two patients were cured only by self-blood injection once and eight patients were cured by self-blood injection twice in one month to two years follow-up. All effects were satisfactory without relapse.

结果 80例病例中经一次性注射自血后，72例获得治愈，8例经二次注射自血而获得治愈，所有病例随访1个月--2年，疗效满意，未见复发者。

To solve the above problems, a novel resonance injection type hybrid active power filter is presented, it allows the energy exchange between the DC-side capacitor and grid, DC-side voltage will be stabilized after the proposed control method base on the regulation of reactive current is adapted. On the other hand, a new current control method is proposed which is based on the control of error between injection current and harmonic current compensated by passive power filter using recursive PI.

在此基础上结合提出的基于基波无功电流闭环调节的直流侧电压控制方法，保证了直流侧电压的稳定；提出了采用递推积分将无源滤波器作用后电网谐波电流与注入支路补偿电流进行闭环比较控制以获得参考电流的方法，减小了误差，提高了系统的控制精度。

Methods The compound red-rooted salvia injection is used to treat child refractory nephropathy by intravenous infusion.2.5~7 years old patients should receive injection 5~6 ml/time/day.

方法在以复方丹参注射液静脉滴注治疗儿童顽固肾病，2·5~7岁5~6ml/次/d，大于7岁以上10ml~15ml/次/d，7d为一疗程，间隔2周，反复4~6个疗程。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷