查询词典 injection

The paper analyzes the fuel injection control strategy and provides the calculation method of engi- neer load and injection measuring width.The correcting reasons,calculation method and effect of many cor- rections are also given.

主要对电子燃油喷射系统喷油控制进行分析，详细给出了发动机负荷、喷油脉宽的计算方法，同时也给出了各修正量的修正原因、计算方法和影响效果。

The results indicated that the Nao Weizhi Injection diluted properly had no interference in TALT.So the TAL could be used to test the bacterial endotox in the Nao Weizhi Injection and substitute RT for the pyrogens test.

结果表明，脑维治注射液经适当稀释对用鲎试剂检查其中的细菌内毒素无干扰，鲎试剂法可以用于脑维治注射液细菌内毒素检测，以替代家兔法检查热原。

Joint-seal Glue Injector is a small device which is used to inject the glue into the concrete joint with the pressure, adopting the glue-injection piston and spring structure design, without the glue bag, fixing the piston in the front the push rod, installing the high strength spring onto the push rod, after release the lock latch of the push rod, pushing the piston and the push rod forward with the tensile force of the high strength spring, so pressing all of the glue liquid from the glue-injection cylinder into the joint.

灌缝胶注胶器是一种对混凝土裂缝持压注胶的小型设备，采用注胶活塞和弹簧的灌缝胶注胶器结构的改进，舍去了胶囊，通过在推杆前端固定注胶活塞，在推杆上套置高强度弹簧，在松开推杆的锁扣后，利用高强度弹簧的张力，可推动注胶活塞连同推杆前移，将注胶筒内的胶液完全压出注入建筑结构的裂缝中，价格低廉，性价比高，操作方便，施工安全，清洗方便，可多次重复使用。

What this article introduced is planet gear's injection mold design, the content and applies, the design criterion as well as the product synopsis including the plastic injection mold's principle of work.

本文介绍的是行星齿轮的注塑模具设计，内容包括塑料注塑模具的工作原理及应用、设计准则以及产品的简介。

It is the first time to compare the emission of the premixing LPG/diesel dual fuel engine with that of the mixing injection LPG/diesel dual fuel engine. The results state that the NO〓 emission of the premixing dual fuel engine is lower than that of mixing injection dual fuel engine in the whole loads, but the emission of HC and CO is reverse.

研究结果表明：在整个负荷范围内，预混进气双燃料发动机的N0〓排放明显低于混合喷射双燃料发动机；混合喷射双燃料发动机的HC和CO排放较低；在小负荷二者的烟度相差不大，但在大负荷预混进气双燃料发动机的烟度较低。

Auto parts: Fuel injection system valve follower, plunger piston and fuel injection needle, etc.

汽车零部件：燃料喷射系统、柱塞、喷油针等）、动力传动系统、活塞部件、凸轮轴部件（销、衬套、摇臂及部分液压元件等）和其他部件。

In the present work,Cu nanoparticles with an average size of 20-50 nm were dispersed in diesel fuel oil . A injection pump plunger was in-situ repaired on a 12PSDB75 fuel injection pump by applying auto-reconditioning function of Cu nanoparticles. Mophologies and typicle element distributions of the plunger piston surface before and after repair were analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy.

将平均粒径为20~50nm的铜粉均匀分散到柴油中，在12PSDB75型喷油泵试验台上利用纳米铜微粒的磨损自修复性能，在不拆卸零件的情况下对磨损失效的喷油泵柱塞偶件进行了原位修复，利用扫描电镜、能谱仪等对修复前后柱塞表面进行了形貌与微区成分分析。

MethodsIn the muscle stimulation test, two rabbits were observed at 48 h after injection Yinxingdamo (Freeze-dried Power); In the vessel stimulation, four rabbits were observed on the 5 d after injection Yinxingdamo (Freeze-dried Power), and the reaction after stopped treatment 14 d.

方法肌肉刺激性实验，观察2只家兔注射用银杏达莫后48 h的变化。血管刺激性实验，观察连续用药5 d注射用银杏达莫及生理盐水，以及恢复14 d后的注射局部血管和周围组织反应情况。

80 patients with recurrent oral ulcer were randomly divided into two groups. The treatment group (40 cases) was treated with He-Ne laser and acuppoint-injection with Huangqi injection. The control group (40 cases) was treated with Compound Chlorhexidine and Dexamethasone Pellicles and Metronidazole tablets.

将门诊符合条件的80例复发性口腔溃疡患者随机分为两组：运用激光照射配合穴位注射黄芪注射液治疗复发性口腔溃疡40例作为治疗组，洗必泰口腔溃疡膜溃疡表面敷贴配合甲硝唑片口服40例作为对照组。

Injection parameters such as injection pressure and nozzle diameters were investigated by using the quantitative calibration results.

在改变喷射控制参数和环境参数的喷雾特性研究中，应用定量标定的试验结果深入开展了喷油压力、喷孔孔径、环境密度和环境温度对喷雾各个特性参数影响的研究。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷