查询词典 inertia transmission

Firstly, the transient stability of the modes by which some kinds of huge power suppliers are connected with AC power grid is analyzed and compared in detail; then a detailed transient stability simulation of a certain large-scale demonstration system is performed; finally some helpful conclusions are obtained: in the general situation, the bundling power transmission mode is favorable to increase the stability of sending system; if it is helpful to evidently increase the inertia of the equivalent leading group, the mode that connects the huge power supplier with sending system will be helpful to enhance the stability of sending system, however it is necessary to perform simulation and analysis while these principles are applied to FACT systems.

首先从机制上对几种大电源接入交流系统方式的暂态稳定性进行了详细的分析和比较；然后对大型算例系统进行了详尽的暂态稳定仿真；最终得出了一些有用的结论：一般情况下，打捆送电方式有利于提高送出系统的稳定性；如果有助于显著增加领前群的惯量，则与送端系统相联的方式也有助于提高送电系统的稳定性，但仍要结合具体系统进行分析。

To match the load characteristic of shoe tree CNC machine tool's transmissionsystem more reasonably ,minimize the moment of inertia and react to the change ofvelocity and acceleration in every axis quickly ,this paper introduces a method ofbuilding the mathematics model based on motor′s load to optimize the transmissionsystems ,distribute the total speed rate and analyse the transmission systems to chosethe best transmissionscheme.

为了实现鞋楦机床数控进给传动系统负载特性的更好匹配，使各轴能够快速地响应速度和加速度的变化，建立了基于电机负载的传动系统数学模型，分析了各个相关动力参数对电机负载的影响，进行了传动系统速比的优化、进行了载荷的匹配、确定了最佳的传动方案和动力参数以实现电机的负载最小。

The non-linear dynamic equation of spiral bevel gears and hypoid gear drives is established, which includes the input and output rotating inertia, transmission error, time-varying mesh stiffness and backlash.

建立了弧齿锥齿轮和准双曲面齿轮非线性系统动力学方程。这个方程中包括了输入和输出惯量、传动误差、时变啮合刚度、时变啮合阻尼及间隙。

Normal inertia flywheel, fV belts transmission.

常规惯性飞轮， V 带驱动

By analyzing the engine driving torque characteristics and the transmission inertia torque while speed ratio is changed under transient condition, a new synthetic control algorithm is developed which can approach engine target torque by compensating engine output torque with transmission system inertia torque.

本文从金属带式无级变速传动的传动机理入手，通过建立发动机和无级变速器的速比变化率模型，研究了发动机与无级变速器的匹配控制策略。

This routine insured the research work finished in limited term. Since the torque coupling increases the inertia of transmission input shaft, the conventional AMT control technology can not control shifting process well.

针对并联双轴混合动力汽车换挡时同步时间过长的问题，提出换挡主动控制理论，即换挡过程中应用电机主动调节变速器输入轴的同步转速，以缩短同步时间。

When inertia force ofa transmission shaftdoesnotchange, itsmaximum transversaldisplacement is equal to the sum of the static deflection produced by inertia force and gravity and the amplitude ofdeflection induced by eccentric mass, and when inertia force of a transmission shaft changes, dynamic deflection is produced.

惯性力不变时，传动轴的最大横向位移等于惯性力和重力产生的静挠度与质量偏心产生的动挠度幅值之和；惯性力变化时，传动轴产生动挠度。

There are six major parameters impacting vehicle handling and stability performance: the cg location, the rigidity of tyre side list, the rigidity of steering system, the steering system transmission ratio, the rear axle roll steering coefficient and the entire vehicle circling the vertical axis the rotating inertia.

对操稳性影响较大的主要有6个参数：重心位置、车轮侧偏刚度、转向系刚度、转向系传动比、后轴侧倾转向系数及整车绕垂直轴的转动惯量。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。