查询词典 inequality constraint

In chapter seven, the pricing regulation model of power transmission and distribution is studied. In this paper, the incentive mechanism models are designed under asymmetry information about product cost and market demand, which can induce the utility company to report true private type and control the over price successfully. The models can the incentive compatibility constraint and participation constraint required for participants and can maximize social welfare.

本章对管制者分别在企业成本和消费需求两种信息不完全的情况下，运用激励理论对需求确定和需求不确定两种状况设计对垄断输配电企业在满足参与约束和激励相容约束的激励机制真实披露真实成本的私人信息以使社会福利最大化的目的展开研究。

In order to assure matching, a new matching method consisting of several algorithms has been proposed to avoid the failure of 3D reconstruction. The method first gets a set of candidate matching points in the other image for a feature point with epipolar constraint, and reorders the candidate points with similarity constraint, and finally determines the best correspondence for every feature point.

为保证图像匹配正确，避免三维重建失败，提出了一种适合本课题的综合匹配算法，先利用外极线约束获得一个特征点在另一幅图像中的候选匹配点集合，接着根据相似性约束对候选点排序，最后根据位置约束和唯一性约束确定最后匹配。

Right-click the constraint Angle SHAFT TURN (180.00 deg) and clear the Suppress box to activate the constraint.

在约束 「Angle SHAFT TURN (180.00 度)」上按一下右键，并清除「抑制」方块以启用约束。

This paper draw the Critical Chain Technology based on Theory Of Constraint to make the network schedule plan, promote the resource constraint to activity logical relations with the same level, indicate to replace the Critical Path by Critical Chain.

本文将基于约束理论的关键链技术引入网络进度计划的编制中，将资源约束提升到与工序逻辑关系同等的高度，主张采用关键链取代关键路线。

The article simply expounders the Theory of Disequilibrium Transportation Planning on the basis of analyzing the causes of traffic congestion problem,and analyses the urban transportation planning rigid constraint qualification, sequentially,educes concrete limit constraint qualification,provides a certain theoretical basis and design parameters to transportation planning.

文章在分析交通拥挤问题原因的基础上，简单阐述了非均衡交通规划理论，并基于该理论分析了城市交通规划的刚性约束条件，得出了具体的边界约束条件，为交通规划提供了一定的理论依据和设计参数。

The feed motion is projected into each feed axis, and based on its mechanical model(motor driving torque/force, Inertial force and cutting force), the constraint relationship between feedrate, feed acceleration, and feed drive capabilities and toolpath geometric characteristics is derived. With this constraint model, the acceleration and deceleration of each axis can be limited within its capability.

将进给运动分解到各运动轴，根据机床进给轴的力学(电机驱动力／力矩、进给系统所受的惯性力及切削力)模型，推导了多轴联动加工时进给速度、加速度与各进给轴驱动能力以及加工路径几何特性之间的约束关系，使得加工过程中机床各运动轴的加减速始终处于其加工能力范围内。

Third two adaptive methods of regularized factors are put forward based on the relations of data object function, model constraint object function, and regularized factor. ARIA is used to solve the one_dimensional inversion by MT data by the constraint of the flattest model.

本文详细阐述了最平缓模型约束下的大地电磁一维连续介质反演的ARIA实现，以几个算例的分析比较来说明ARIA的有效性。

Comparison of case calculations indicates that different site sets may require varied methods to construct optimal grids. Among them the "optimized dynamic allocation under flattest model constraint", and "optimized dynamic allocation under smoothest model constraint" are most adaptive, by which the constructed grids have fairly smooth grid spacing and smaller site shifts.

算例对比研究表明，对于不同的测点集，最佳网格构建的方法可能不相同，但其中&最平模型约束动态配点法&、&最光模型约束动态配点法&拥有最强的适应能力，它们在各种情况下所构建的网格一般同时具备较光滑的网格间距变化和较小的测点偏离程度。

The constraint conditions of quasi optimal and strict optimal OOCs constructed by recursive method are theoretic analyzed. Based on these constraint conditions, as the initial conditions of OOCs obtained by direct construction, some quasi optimal and strict optimal OOCs with larger code length and sizes are obtained by recursive method.

2理论研究了基于递归法构造准最佳和严格最佳光正交码的约束条件，在此基础上，以直接构造法得到的光正交码为初始条件，利用递归法构造了一些具有相同相关特性的码长更长、容量更大的准最佳和严格最佳光正交码。

In this paper, a novel two-layer constraint image interpolation model is proposed. The novel model interpolates image under the constraint of gradient magnitude in original un-interpolated image.

摘要该文提出一种双层约束的图像插值模型，模型在原始未插值图像梯度模约束下同时基于局部和全局信息处理。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。