查询词典 increase speed

Researches show that the drive force characteristics of the electric tractor drive system based on series DC motor is close the ideal characteristics, the curves are concave, low speed with constant power, and high speed with constant torque; the electric tractor has large working speed under different shifts, but the extensive coincidence speed shows that the variable ratio of the gear is unreasonable; the maximum climbable gradient of this electric tractor is more than 30%, and does not need frequent shift when working for its extensive climbable gradient; there are many influence factors of continuous working time, which the more obvious factors are working speed and working load, the working time increases with the increase of the working speed and working load.2. Simulation researches on the drive characteristic of the electric tractor.

研究结果表明：基于串励直流电动机(来源：ABC21论文网www.abclunwen.com)的电动拖拉机电驱动系统的驱动力特性场接近理想驱动力特性场，其各挡下的驱动力特性是一组下凹的曲线，低速恒转矩，高速恒功率；同一行驶速度下所对应高挡驱动力大于低挡驱动力，这是由电机的调速特性决定的；电动拖拉机各个挡位下具有较广的稳定作业速度范围，但是各个挡位之间速度重合的范围较多，说明所用变速箱变速比与电动机匹配不合理；电动拖拉机最大爬坡度达到30%以上，并且各挡爬坡度变化范围较广，作业过程中不需要频繁换挡；影响电动拖拉机连续作业时间的因素较多，其中作业行驶速度和作业负荷影响最为明显，作业负荷越大，连续作业时间就越短，作业速度越快，连续作业时间就越短。2、电动拖拉机驱动特性仿真研究。

6"Ball cover, Features beauty,refinement; The precise step enters the electrical engineering to drive, go placidity,go to nicety;shift aptitude, Horizontal speed 0.5°/s---240°/s ,Vertical speed 0.5°/s---200°/s;Vertical running have function to "Auto-flip, 360°continous horizontal flip;Dome speedauto-shift--- The speed of housing become the zoom lens depth to increase its speed pro rata lower gradually, a little bit on guard function; Auto-focus,auto-iris,Tum to surge and lightning strike protector;Menu setup and control function,estate memory before break off electricity and auto-resume

6英寸球罩，外型美观、精巧；精密步进电机驱动，运转平稳，定位准确；智能变速，0.5°/S－240°/S水平变速，0.5°/S-200°/S垂直变速；垂直转动有"自动翻转"功能， 360度持续水平转动；云台速度自动调整—云台的速度随变焦镜头深度的增加其速度按比例逐渐降低，守望点功能；自动聚焦，自动光圈，内置浪涌及雷击保护装置；菜单设置及控制功能，断电前状态记忆及来电自动恢复功能；64个预置点

6"Ball cover, Features beauty,refinement; The precise step enters the electrical engineering to drive, go placidity,go to nicety;shift aptitude, Horizontal speed 0.5°/s---240°/s ,Vertical speed 0.5°/s---200°/s;Vertical running have function to "Auto-flip, 360°continous horizontal flip;Dome speed auto-shift--- The speed of housing become the zoom lens depth to increase its speed pro rata lower gradually, a little bit on guard function; Auto-focus,auto-iris,Tum to surge and lightning strike protector;Menu setup and control function,estate memory before break off electricity and auto-resume fuction in come to electricity; 64initialize spots,5 auto-patrol path;Contain multi-confer;485standard communcation interface;Function to give an alarm to linkage.

6英寸球罩，外型美观，精巧；精密步进电机驱动，运转平稳，定位准确；智能变速，0.5°/S-240°/S水平变速，0.5°/S-200°/S垂直变速；垂直转动有"自动翻转"功能， 360度持续水平转动；云台速度自动调整—云台的速度随变焦镜头深度的增加其速度按比例逐渐降低，守望点功能；自动聚焦，自动光圈，内置浪涌及雷击保护装置；菜单设置及控制功能，断电前状态记忆及来电自动恢复功能；64个预置点， 5条自动巡视路径；兼容多种协议；标准485通讯接口；报警联动功能。具有球机环境温度和摄像机角度数显功能。

When other technics conditions are certain, we use the globosity aluminum powder of different particle diameter a to grind the flake of aluminum powder , with the particle diameter increase of the globosity aluminum powder, the particle diameter of the flake of aluminum powder will also become bigger immediately. 3, The ratio of grinding ball to aluminum powder is 20:1. 4,the grinding speed is 38 and 33 r.min alternate once h-our in the first 10 hours, and use the speed of 29 and24 per hour alternating revolving speed in the last 5 hours, this speed is fine to grind the flake of aluminum powder. 5, wet method ball-milling mainly adopt of help-milling agent as Bl. 6, influence of the research grinding time.

经系统的研究，得出如下结论：1、基本参数：采用200升球磨机，装入钢球200kg，原料铝粉：溶剂量=1：2，铝粉：钢球=1：20；2、当其它工艺条件一定时，用不同粒径的球状铝粉作为原料磨制片状铝粉，随着原料铝粉的粒径增大，所制得的片状铝粉的粒径也会随之增大。3、球料比我们控制在20：1.4、研磨前10小时采用速38和33r.min每小时交变一次，后5小时用29和24每小时交变的转速，这个速度是适宜磨制片状铝粉的。5、湿法球磨片状铝粉主要采用的助剂为复合助剂B1.6、研究研磨时间的影响。

Three kinds of cutting material were selected to machine stainless steel machining experiment such as ceramic cutting tools, cermets cutting tools and coated carbide cutting tools, in which the best range of each kind of tool material was founded. For example, LT55 was suitable to be machine lCrl8Ni9Ti as the cutting speed surpasses 120m/min and have a good wearable property.(3) Surface roughness was measured under different cutting conditions. Feed rate played the most important role in impacting surface roughness, and then cutting speed.(4) Chip patterns in different cutting speed with various cutting materials were analyzed. With the increase of turning speed, chip became shorter and was easy to be broken. For instance, serration chip appeared in high sped turning stainless steel with LT55;(5) Work hardening of austenitic stainless steel was analyzed.

陶瓷刀具LT55适合在Vc=120m/min以上切削加工不锈钢，耐磨性好；③通过试验研究了不同刀具材料高速车削加工1Cr18Ni9Ti不锈钢时的表面粗糙度，其中进给量对表面粗糙度的影响最为显著，其次为切削速度；④分析了不同刀具材料在不同切削速度下加工1Cr18Ni9Ti不锈钢的切屑形态，随着车削速度的提高，切屑变短且易断屑，其中LT55陶瓷刀具切削加工时产生了锯齿状切屑；⑤分析了奥氏体不锈钢的加工硬化机理及其对刀具磨损的影响；⑥根据试验结果分析在不同切削条件下切削不锈钢的刀具磨损形式及其磨损机理。

The result makes clear: EThe tensile strength of TFE film increases somewhat along with the addition of drawing speed, and rupture outspread rate reduces;ETFE to succumb filmily somewhat along with the addition of drawing speed the addition that intensity follows drawing rate and increase somewhat, but the 2nd succumb intensity increases not big;ETFE to succumb filmily meet an emergency follows drawing rate increase somewhat, the 2nd succumb the amount of tangent and stretch model that meet an emergency reduces;ETFE film somewhat and model of the 2nd flexibility measure those who follow drawing rate to increase show downtrend, quantity of secant flexibility model and quantity of the 3rd stretch model do not have apparent change.

结果表明：ETFE薄膜的抗拉强度随拉伸速度的增加略有增加，而断裂延伸率随拉伸速度的增加略有减小；ETFE薄膜的屈服强度随拉伸速度的增加而有所增加，但第二屈服强度增加不大；ETFE薄膜的屈服应变随拉伸速度的增加略有增加，第二屈服应变则略有减少；ETFE薄膜的切线弹性模量以及第二弹性模量随拉伸速度的增加呈下降趋向，割线弹性模量和第三弹性模量则没有明显的变化。

The calculation results shows that ,(1) when the rotor rotates at the working speed, a local regurgitant whirlpool that is rightabout to the rotor"s rotating direction appears in the classifying region, which makes the separated granules come back to the outside of the classification district and influences the classification efficiency of the turbine classifier;(2) in the condition of a low rotating speed of turbo rotor, ultrafine particles can follow the gas phase by and large, but when the rotating speed increases, a phenomenon of velocity slippage between two phases appears evidently;(3) A operating parameter, air flow rate is so important that can directly influence the stability of flow field in classifying chamber, the bigger the air flowrate is , the steadier the flow field is;(4) Compared with straight blades, the new shape of blades with backward crooked elbow are helpful to improve the stability of flow field and form whole stream easily, also beneficial to advance the classification accuracy and classification efficiency;(5) The motion trace of particles are very complicated when the turbo rotor rotates at a high speed, the constant bounce of the particles appear between the blades and the coarse particles are even bounce back from the inlet, only the finer can pass through the classification area from the oulet;(6) Along with the increase of the rotor"s rotating speed, radiah axial and tangential velocity all begain to fluctuate repetitively like sine-wave, the smaller the particles are, the more violently they fluctuates.

数值模拟结果表明，(1)在涡轮达到工作转速时，在分级区域形成了一个与涡轮旋转方向相反的局部回流涡，它使得分离出来的细粒重又被带回分级轮外边缘，从而严重影响分级机的分级效率；(2)粉尘粒子在涡轮低速运动情况下，基本上能跟随气体运动，但随着转速加大，两相之间出现了明显的速度滑移现象；(3)分级机工作时的风量也是一个比较重要的操作参数，它可以直接影响到分级机内腔流场的稳定性，风量越大，流场越稳定；(4)同直叶片形状相比较，带后弯导板的叶片，有利于改善流场的稳定性，流场容易形成整体流，对提高分级效率和分级精度都非常有利；(5)粒子轨迹线在涡轮转速较高时十分复杂，有的出现了反复的弹跳现象，大颗粒不能通过分级区域而从进口返流了，只有细小的颗粒才从出口处流出；(6)涡轮转速加大时，粒子的径向、轴向和切向速率出现了明显的类似于正弦波的脉动现象，颗粒越小，脉动程度越为剧烈。

By regression of experimental data, therules of the linkage between these factors, which will provide a theoretical basis for designing BBP with different scales.3 Using thermal analysis technology and dynamic thermogravimetry, the paper studies combustion kinetic characteristics of 3 types of agricultural crops at different rate of temperature rise, and thus, achieved dynamic parameters of these fuels at different rate of temperature, established dynamic model of straw combustion, which reflects the dynamic process in the fast combustion area.4 Characteristics of straw briquette combustion was experimented, focusing on the impact of straw type, temperature, air supply, and density, diameter, and weight of briquette on the combustion speed, and the following conclusions were drawn:(1) combustion of straw briquette fuel is static permeation diffusion combustion;(2) temperature has a larger impact on the speed of straw briquette combustion than air supply; the higher the combustion temperature is, the faster volatilizable component separates out, and the less steady the combustion is;(3) density of briquette fuel has impact on the speed of volatilizable component separation and therefore the combustion speed;(4) increase of diameter and weight of briquette fuel increases the average combustion speed in the initial stage, and that in the later stages is comparatively steady;(5) the proportion of volatilizable component in straw briquette fuel is high, therefore, the temperature control during combustion under the rational ventilation condition is essential to ensure its safe combustion.5 Using the above-mentioned results of experiments and theoretical analysis, and based on thought of hydraulic driven and bi-direction compression, the hydraulic system and compression parts of the HBP BBP are re-designed in terms of industrialization.

利用热分析技术，采用动态热重实验法，对我国的三大农作物秸秆在不同升温速率下的燃烧动力学特性进行了较系统的研究。得到了各原料在不同升温速率下的动力学参数；建立了秸秆燃烧的动力学模型，该模型反映了秸秆迅速燃烧区的动力学过程。 4 对秸秆成型燃料的燃烧特性进行了试验研究。着重研究了秸秆河南农业大学博士学位论文巫的种类、温度、空气供给量、成型燃料密度、直径、质量对成型燃料燃烧速度的影响并得出如下主要结论：①秸秆成型燃料的燃烧方式属于静态渗透式扩散燃烧。②秸秆成型燃料燃烧速度受温度的影响大于通风量燃烧速度的影响：燃烧温度越高，挥发分析出速度越快，燃烧平稳性愈差。③成型燃料密度影响成型燃料挥发分的析出速度，影响燃烧速度。④成型燃料直径和质量的增加，使得燃烧初期的平均燃烧速度增大，中后期的平均燃烧速度相对平稳。⑤秸秆成型燃料含挥发分比例高，因此合理配风下的控温燃烧是保证其完全燃烧的关键。 5运用已取得的试验和理论分析结果，以液压驱动、双向成型为基础，从产业化的角度对HBP型成型机进行了液压系统和成型部件的改进设计；同时采用了二级预压机构，使该成型机的生产率达到 500kg.hd；单位能耗 60kwh。上'左右，磨损件修复周期 300小时左右，基本解决了影响生物质固化技术在国内推广的技术难题。

This requires us to burn the disc, the first should be a relatively low speed to burn, if burn everything normal circumstances, there is no instability, we further increase the speed of the burner is now almost provide 1-speed, 2 speed, 4 speed options, and many other items, we recommend the use of小编for 2x recording, if the situation is not normal, we can take timely remedial measures.

这就要求我们在刻录光盘的时候，首先应该以比较低的速度来刻录，如果刻录的情况一切都正常，没有任何不稳定的情况时，我们再提高速度，现在的刻录机几乎都提供1倍速、2倍速、4倍速等很多个选择项，小编推荐大家采用2倍速来进行刻录，如果情况不正常，我们能够及时的采取补救措施。

6"Ball cover, Features beauty,refinement; The precise step enters the electrical engineering to drive, go placidity,go to nicety;shift aptitude, Horizontal speed 0.5°/s---240°/s ,Vertical speed 0.5°/s---200°/s;Vertical running have function to "Auto-flip, 360°continous horizontal flip;Dome speed auto-shift--- The speed of housing become the zoom lens depth to increase its speed pro rata lower gradually, a little bit on guard function; Auto-focus,auto-iris,Tum to surge and lightning strike protector;Menu setup and control function,estate memory before break off electricity and auto-resume fuction in come to electricity; 64initialize spots,5 auto-patrol path;Contain multi-confer;485standard communcation interface;Function to give an alarm to linkage.

6英寸球罩，外型美观，精巧；精密步进电机驱动，运转平稳，定位准确；智能变速，0.5°/S-240°/S水平变速，0.5°/S-200°/S垂直变速；垂直转动有&自动翻转&功能， 360度持续水平转动；云台速度自动调整—云台的速度随变焦镜头深度的增加其速度按比例逐渐降低，守望点功能；自动聚焦，自动光圈，内置浪涌及雷击保护装置；菜单设置及控制功能，断电前状态记忆及来电自动恢复功能；64个预置点， 5条自动巡视路径；兼容多种协议；标准485通讯接口；报警联动功能。具有球机环境温度和摄像机角度数显功能。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。