查询词典 inclined shaft

The reverse force self-expansion rivet as one fastener part has one small head and one small-diameter neck in the root part as well as one integral expansion sheet with the same diameter as the shaft in between.

目前国内外所使用的《胀钉》是螺杆式的《他胀钉》，它构件多，成本高。因此，本人发明了简易的《反力自胀铆钉》来满足各种材料的铆制紧固上。其结构特点是在钉杆根部有直径偏小的颈部和小头，还在其间有与杆同径连体的胀片。

The damage reasons of shaft seal for HP cylinder of CO 2 compressor are analyzed,and the improvement measure is give

分析二氧化碳压缩机高压缸轴端密封损坏的原因，并提出了改进的措

The results show screw-down tilting is the basic reason of the problem. When there is an obliquity between the shaft sleeve and bush which is caused by screw-down tilting, the load capacity of the bearing drops suddenly.

计算结果表明，压下倾斜过大会造成轴套与衬套的轴线出现倾斜，进而导致轴承的静压承载能力急剧下降，是造成轴承寿命缩短、连轧机启动频繁失败的根本原因。

Bearing and shaft fastening methods are: the outer sleeve with eccentric spherical bearing, the eccentric sets Presentation at the bearing inner ring of the eccentric stage, along the axis of rotation direction of tightening eccentric sleeve, and then wrench tighten the screw Hexagon eccentric sleeve on the set screws can be.

轴承与轴的紧固方法是：对带偏心套的外球面轴承，将偏心套套在轴承内圈的偏心台上，沿轴的旋转方向拧紧偏心套，再用内六角螺钉扳手拧紧偏心套上的紧定螺钉即可。

This paper presents the Machining Tool geometry of the former flank, the main flank, flank, the main cutting edge, Under the cutting edge tip cutting plane, the main section, the former Kok, horn, wedge angle edge angle, pointed knife, the blade angle, vice horn, Under the Frontier concept, the concept of cutting consumption, and the general circumstances of their choice method for processing slender shaft. cast iron materials, aluminum, stainless steel, rubber materials, plexiglass material, cloth bakelite materials, high temperature alloys, aluminum-magnesium alloy, hardened steel, the typical trapezoidal thread, the thread Triangle, Speaking at the trapezoidal screw thread pitch of the Tool geometry of the selection methods and cutting the amount of cutting fluids reasonable choice.

本文介绍了在机械加工中车刀几何角度中的前刀面、主后刀面、后刀面、主切削刃、副切削刃刀尖切削平面、主截面、前角、后角、楔角主偏角、刀尖角、刃倾角、副后角、副前角的概念、切削用量的概念、以及一般情况下的它们的选择方法，进行加工细长轴、铸铁材料、铝合金、不锈钢、橡胶材料、有机玻璃材料、夹布胶木材料、高温合金、铝镁合金、淬火钢、典型梯形螺纹、三角螺纹、特在螺距的梯形螺纹等的车刀几何角度的选取方法切削用量及切削液的合理选择。

Specializing in the production of a variety of fans, car parts, computer connectors, F head, shell, hexagonal screw, nut, electrical appliances, lighting, toys, plugs, partial mandral, photocopiers shaft axis and the kinds of hardware parts, such as manufacturing, a variety of fixed pieces, standards and non-standard screws, nuts and so on.

专业生产各种风机、车件、电脑接插件、F头、外壳、六角螺丝、螺母、电器、灯饰、玩具、插头、偏芯轴、复印机轴及种轴类等五金零件制造，各种固定件、标准及非标准螺丝、螺母等。

The sludge residence time in the screw press and thus the filtration time can be adjusted to individual requirements by adjusting the rotational speed of the screw shaft.

污泥停留在螺旋压力机的时间，过滤的时间可以根据实际情况通过改变螺杆轴转的速调整。

Open water before the gas plug screw, and then adding water until the run out from the pore water release, and then a few rotating shaft, such as to continue to take water that has been filled with water, and then close the gas plug, ready to start.

灌水前拧开放气螺塞，然后加水，直到从放气孔向外冒水，再转动几下泵轴，如继续冒水，表明水已充满，然后关闭放气螺塞，准备起动。

Linear shaft, bearing, guide, joint bearing, slide unit, ball screw, machinery parts...

直线轴，轴承，导轨，滚珠丝杠，关节轴承，滑动单元，机床附件等

In the part of mechanical design, The output shaft of stepping motor connects ball screw with coupling joint, and enables worktable auto-reciprocating under the support of linear rack.

关于机械设计部分，电机输出轴经过联轴器连接滚珠丝杠带动工作台运动，工作台在直线导轨的支撑下做直线往复运动。

Alternatively, the con- trollers can use the synchronous rectifier itself or loss- less inductor current-sensing methods to provide overload protection with lower power dissipation.

另外，康威特罗勒斯可以使用同步整流器本身或亏损减少电感电流检测方法，以提供低功耗过载保护。

Mr. Dauber's other Schatz hangs in his home movie studio.

多伯把沙兹的另一件作品挂在家里的电影室。