查询词典 inclined shaft

The ECS drive shaft equalizes the speed between the drive shaft and the wheel.

精英传动轴均衡的速度之间的传动轴和车轮。

Check effect after 15 minutes, with the standard that every shaft drawed out 1-2 times longer and if it rolled on finger without rebound if the shaft broken when drawing, that means it didn't intenerated enough, or the hair belongs to rebellious hair. Re-intenerate if needed

：15分钟后检查，看软化情况是否到位，以发丝能拉长1-2倍，并能在指头绕圈而不反弹为准（如果发丝在拉伸时断掉，则表示头发还未软化，或遇到极度抗拒的发质，40分钟也软化不到位，则冲水，吹干，重新软化）。

We start from the principle that when a shaft is bent and then released, the stiffer the shaft, the faster it unbends or straightens or unload...

我们从拍子由弯曲到释放（即回复到伸直状态，回弹）的原理上讲起：拍杆越硬，拍子伸直得越快。

Finally, the finite element analysis for the IT shaft of the driving system is fulfilled by using ANSYS 8.0 and the stresses and deformations curves of the Π shaft are obtained. The paper else gives a study on few underprops and a reasonable project about few underprops is obtained.

最后利用有限元分析软件ANSYS 8.0完成传动箱Ⅱ轴零部件静态有限元应力和应变分析，得到Ⅱ轴零件在受载情况下的应力应变图，并对各种支撑情况进行了研究，提出合理的径向轴承布置方案。

The first mechanical concept was double shaft wobble-plate configuration with motor output delivered directly to the drive shaft by means of a precision angle gear.

第一机械概念是双重轴摆动板材配置以马达产品被提供直接地对驱动轴通过精确度角度齿轮。

The crossing angle between the driving shaft and the driven shaft is a key parameter that affects the performance of the pump.

万向节机构的输入轴和输出轴的夹角是影响泵性能的一个关键参数。

When taking propeller shaft joint angle measurements, or checking the phasing, of two piece shafts, consider each shaft separately.

当测量两个传动轴的工作角或检查它们是否定相时，对它们要分别考虑。

The meshing of FG drives with misalignment, which includes shaft angle error, shaft crossing error and axial shift error, is analyzed by using the continuous tangency of pinion and FG to obtain the equations of tooth contact analysis, and visualizing contact path, and studying the effect of errors on the shift of it. A computational procedure of tooth contact is developed in this paper.

在具有安装误差的面齿轮传动的啮合分析中，建立了在有轴交角误差、轴交错误差和轴向偏移误差情况下的齿面接触轨迹所满足的方程，提出了一种求解接触点参数的策略；对齿面接触轨迹进行了可视化；分析了各类误差对齿在接触轨迹的影响。

Stroke control valve angle valve shaft should be level so that the fluid contained in the dirt will not be integrated into the valve shaft rotation Shen bearings.

角行程控制阀的阀轴应水平，使流体所含污物不会积沉到阀轴的转动轴承。

In the browser, expand the Pinion Shaft component node, and then select the constraint named Angle SHAFT TURN (180.00 deg).

在浏览器中，展开「小齿轮轴」元件节点，然后选取名为「Angle SHAFT TURN (180.00 度)」的约束。

Alternatively, the con- trollers can use the synchronous rectifier itself or loss- less inductor current-sensing methods to provide overload protection with lower power dissipation.

另外，康威特罗勒斯可以使用同步整流器本身或亏损减少电感电流检测方法，以提供低功耗过载保护。

Mr. Dauber's other Schatz hangs in his home movie studio.

多伯把沙兹的另一件作品挂在家里的电影室。