查询词典 inclined shaft

For SOV energized to counterclockwise drive shaft rotation, reconnect the actuated part to the other end of the drive shaft.

当电磁阀励磁，需要使输出轴向左回转时，只要把输出轴的另一端与被驱动体连接即可。

Inside this hollow shaft, a solid shaft rotated in a spherically seated bearing to carry the blade pitch control spider at its head.

这里面空心轴，实心轴旋转的一球轴承进行坐在其头上的刀片间距控制蜘蛛。

According to geometry model characteristic of shaft and cylinder of steam turbine, a finite element method model of shaft and cylinder was set up.

根据汽轮机转子及汽缸的几何模型的特点建立了转子及汽缸的有限元模型。

Establishing a geometric model of pump shaft with Three-dimensional modeling software and considering force condition to determine the boundary Conditions, after a reasonable simplification, then the modeling is inputted for ANSYS strength analysis combined with the traditional strength theoretical calculations of the shaft to get the result of stress and strain calculations and static stress and strain diagram.

应用三维造型软件建立了泵轴的几何模型，经过合理的简化，分析受力情况确定边界条件，在ANSYS软件中进行分析，结合传统的强度理论计算对泵轴的强度进行了计算和求解，得到了应力和应变的计算结果。

Clean and check 1 slowly loosen the gland nut stuffing, packing the release of residual pressure of all components; 2 Remove all old packing, thoroughly clean axle / rod stuffing; 3 Check the shaft / bar have corrosion, dents, scratches or excessive wear; 4 Check whether there are other WATER POWER CONTROL VALVE parts burr, cracks, wear, they will reduce the packing life; 5 Check whether there is too much stuffing the gap, and the shaft / rod eccentric degree; 6 the replacement of defective parts larger; 7 Check the old packing, as BALANCING VALVES the basis of failure analysis to find the reasons for early failure of packing.

缓慢松开填料函的压盖螺母，释放盘根组件内所有的残余压力； 2）移去所有旧的盘根，彻底清洁轴/杆的填料函； 3）检查轴/杆是否有腐蚀、凹痕、划伤或过度磨损； 4）检查其他零件是否有毛刺、裂纹、磨损，它们会减少盘根的寿命； 5）检查填料函是否有过大的间隙，以及轴/杆的偏心程度； 6）更换有较大缺陷的零部件； 7）检查旧盘根，作为失效分析的依据，球阀以找到盘根早期失效的原因。

Assembly of the torsional spring constant and mass moment of inertia of each equivalent shaft-rotor element and the mass moment of inertia of each rotor yields the mathematical model of the entire shaft-rotor system.

将每一等效旋转轴-转子元素的扭转弹簧常数及质量惯性矩与每一转子的质量惯性矩组合，便可获得整个旋转轴-转子系统的数学模型。

With the development of the electric power industry, the capacitance of a turbo-generator has increasingly become larger, which risk the torsional oscillation in the flexible shaft system of large turbine-generators. The problem of shaft torsional oscillation has become the key technology need to be solved urgently in the development of large power system and unit.

随着电力工业的发展，汽轮发电机组的单机容量正日益大型化，导致机组轴系扭转振动的危害性日益突出，轴系扭振问题已成为发展大电网和大机组所急需解决的关键技术问题。

Based on the shaft partial energy function of the turbine\|generator shaft torsional oscillation.

利用表征重合闸操作影响发电机轴系扭振幅度的等值能量函数，导出了瞬时性故障与永久性故障下重合闸操作对轴系冲击最小的理想重合时刻。

The torsional oscillation problem will make the shaft endure big torque time and again, which produces the fatigue life loss and even makes the shaft broken.

机网扭振相互作用会使机组轴系反复承受较大的扭矩，从而造成疲劳寿命损耗、甚至直接损坏。

So this part will propose a new method based on the EMTDC to analyze the torsional oscillation problem. Since the EMTDC only has the 7 masses shaft model, use the user Module to develop a detailed shaft model.

由于EMTDC现有的轴系多质量块模型最多只能考虑7个质量块，所以基于模态转换与模态降阶的思想利用EMTDC自定义模块重新开发轴系的多质量块模型，使得能对轴系各截面进行考核分析。

Alternatively, the con- trollers can use the synchronous rectifier itself or loss- less inductor current-sensing methods to provide overload protection with lower power dissipation.

另外，康威特罗勒斯可以使用同步整流器本身或亏损减少电感电流检测方法，以提供低功耗过载保护。

Mr. Dauber's other Schatz hangs in his home movie studio.

多伯把沙兹的另一件作品挂在家里的电影室。