查询词典 in-line processing

This paper presents an IFMC CAD model that consits of a geometry model and a material model, in which the geometry space acts as a base space and the material space acts as a bundle space. In this CAD model, the geometry model is based on the non-manifold model. In addition, a half-face data sturucture, which is derived from the half-edge data structure with the non-manifold feature of IFMC taken into account, is adopted to represent the geometry and topology information of the component. For the material model of IFMC, this paper focuses on the FGM component representation firstly and present a simplex-subdivision based CAD data exchange format, in which the material information is represented as a (n-1) simplex and material distributing feature is represented by the interpolation on the simplex-subdivision. Based on those, a part-building orientation optimization algorithm and an adaptive slicing algorithm for FGM component are presented in the paper. For the IFMC material model, the IFMC material information representation is divided into a meso-scale and a macro-scale representation. In the meso-scale, a concept named parameterized periodic functional meso-structure is presented as a unique form to represent the FGM (the homogeneous materials are regarded as a special FGM), the composite and the functional meso-structure material. The model of PMS is a three-tuple that contains the space state informatation, the material parameter and the material meso-scale distribution feature. The macro-scale material information representation is similar to the FGM components by interpolation of the control parameter of the periodical functional meso-structure based on the simplex-subdivision. Through an example of manufacturing-oriented IFMC CAD data processing, it is proved that the IFMC CAD model and the material information representation and process method proposed in this paper can provide a reliable data support for IFMC digital concurrent design and manufacturing.

本文将理想材料零件CAD模型建立在以几何空间为底空间、以材料空间为丛空间的结构上，使用非流形几何模型作为理想材料零件几何拓扑模型的基础，并在半边数据结构基础上，针对理想材料零件的非流形特征局限内部边界上的特点，给出了一个半面数据结构来表述零件的几何拓扑信息；对于理想材料零件的材料模型，本文先从功能梯度材料零件的信息表述与CAD数据交换和处理入手，将材料信息表述为（n-1）维单纯形，然后通过对三维几何区域的单纯剖分，以插值的方式表述零件材料分布特征；在此基础上，根据功能梯度材料零件分层制造中对CAD数据处理的要求，给出了综合考虑零件几何特征与材料特征的生长方向优化算法和自适应切片算法；而对于文中所定义的理想材料零件，本文将其材料信息表述分解到细观和宏观两个尺度进行，首先给出了细观尺度上参数化的周期性功能细结构概念，以此来统一表述功能梯度材料（单质材料作为特殊的功能梯度材料看待）、复合材料和功能细结构材料；把周期性功能细结构模型化为一个包含空间状态信息、材料构成参数和材料细观分布特征参数的三元组，以表达零件的细观材料特征；对于零件宏观的材料变化特征，则同样在几何区域单纯剖分的基础上，通过对细观尺度上周期性功能细结构控制参数的插值来完成；通过理想材料零件CAD数据处理的算例，验证了本文中理想材料零件CAD模型及材料信息表述与处理方法完全可以为理想材料零件的数字化制造提供可靠的数据支持。

This paper presents an IFMC CAD model that consits of a geometry model and a material model, in which the geometry space acts as a base space and the material space acts as a bundle space. In this CAD model, the geometry model is based on the non-manifold model. In addition, a half-face data sturucture, which is derived from the half-edge data structure with the non-manifold feature of IFMC taken into account, is adopted to represent the geometry and topology information of the component.For the material model of IFMC, this paper focuses on the FGM component representation firstly and present a simplex-subdivision based CAD data exchange format, in which the material information is represented as a (n-1) simplex and material .distributing feature is represented by the interpolation on the simplex-subdivision. Based on those, a part-building orientation optimization algorithm and an adaptive slicing algorithm for FGM component are presented in the paper.For the IFMC material model, the IFMC material information representation is divided into a meso-scale and a macro-scale representation. In the meso-scale, a concept named parameterized periodic functional meso-structure is presented as a unique form to represent the FGM (the homogeneous materials are regarded as a special FGM), the composite and the functional meso-structure material. The model of PMS is a three-tuple that contains the space stateinformatation, the material parameter and the material meso-scale distribution feature. The macro-scale material information representation is similar to the FGM components by interpolation of the control parameter of the periodical functional meso-structure based on the simplex-subdivision.Through an example of manufacturing-oriented IFMC CAD data processing, it is proved that the IFMC CAD model and the material information representation and process method proposed in this paper can provide a reliable data support for IFMC digital concurrent design and manufacturing.

本文将理想材料零件CAD模型建立在以几何空间为底空间、以材料空间为丛空间的结构上，使用非流形几何模型作为理想材料零件几何拓扑模型的基础，并在半边数据结构基础上，针对理想材料零件的非流形特征局限内部边界上的特点，给出了一个半面数据结构来表述零件的几何拓扑信息；对于理想材料零件的材料模型，本文先从功能梯度材料零件的信息表述与CAD数据交换和处理入手，将材料信息表述为(n-1)维单纯形，然后通过对三维几何区域的单纯剖分，以插值的方式表述零件材料分布特征；在此基础上，根据功能梯度材料零件分层制造中对CAD数据处理的要求，给出了综合考虑零件几何特征与材料特征的生长方向优化算法和自适应切片算法；而对于文中所定义的理想材料零件，本文将其材料信息表述分解到细观和宏观两个尺度进行，首先给出了细观尺度上参数化的周期性功能细结构概念，以此来统一表述功能梯度材料(单质材料作为特殊的功能梯度材料看待)、复合材料和功能细结构材料；把周期性功能细结构模型化为一个包含空间状态信息、材料构成参数和材料细观分布特征参数的三元组，以表达零件的细观材料特征；对于零件宏观的材料变化特征，则同样在几何区域单纯剖分的基础上，通过对细观尺度上周期性功能细结构控制参数的插值来完成；通过理想材料零件CAD数据处理的算例，验证了本文中理想材料零件CAD模型及材料信息表述与处理方法完全可以为理想材料零件的数字化制造提供可靠的数据支持。

The electronic heating evaporator in the high-side gravity recirculation system in ANSI/ASHRAE 64-2500 standard is replaced by a new type plate evaporator which is more effcient and energy-saving, because the cold water outlet from the evaporator that is used to heat the cryogen can be used once again to cool the air in the air inlet trunk; an air processing unit is designed in the lab design, so to imitate all kinds of weather in each season in every location of China at any time the test is being made; the data selection system can send all the data in the test to the computer at one time, and to reduce the cost of the test some data which is more stable are read manually through traditional meters if this can not sacrifice the precision of the test.

本文的设计中用效率更高的新型板式换热器代替了原ANSFASHRAE 64——2500标准中压缩驱动循环系统中的电加热蒸发器，加热冷剂后得到的低温淡水还可以用于冷却进气通道中的空气，不仅提高了效率，而且更加节能；实验室方案中增加了空气处理系统，可以实现随时对全国各地各季节的空气状态进行模拟，方便实验的进行；采用数据采集系统将数据整体采集到电脑中方便数据处理，而且对于变化频率不高相对较为稳定的数据采取传统仪表进行人工读数，在保证测试结果准确性的前提下降低了成本。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

The hardware design project and principle are presented in detail, including the sensor and the single-chip microcomputer select, the signal processing circuit, the real-time clock circuit, the alarm circuit, the wireless receiving and transmitting circuit, the extension of FLASH memorizer, the key-board circuit and USB interface circuit, etc. As the counterpart, the software function modules are presented as well, including the main program of transmitter and receiver, the data acquisition and processing module, the display function module, the key function module, the three-level alarm on fault parameters module, the fault parameters memorizing and inquiring module and the wireless transmitting and receiving module, etc.

论文详细介绍了系统的硬件设计方案及其工作原理，包括传感器的选择、单片机的选择、信号调理电路、实时时钟电路、报警电路、FLASH存储器、无线发射与接收电路、键盘电路和USB接口电路等；同时详细介绍了软件设计方案及具体实现方法，包括发射机主程序、接收机主程序、数据采集与处理模块、键盘处理模块、故障数据存储与查询模块、显示功能模块、报警模块、无线发射与接收模块等。

Its innovative expertise, launched in 2004 to ultra-exclusive processing Showcase (patent number: 200530094174.0), the entire processing site has been recognized by consumers, but also won the affirmation of partners.

以其新颖的专业技术，在 2004 年推出了商超专用加工展示台（申请专利号： 200530094174.0 ），整个加工现场取得了消费者的认可，也赢得了合作伙伴的肯定。

Sentence processing is an important issue in psycholinguistic research,which focuses on factors related to sentence processing .

句子加工是心理语言学研究的重要内容，主要关注影响加工过程的因素。

MYSELF AND MY INDIAN PROCESSING FRIEND HAS STARTED PROCESSING OF JELLYFISH IN SRILANKA.

我和我的朋友已经开始在斯里兰卡开始海蜇加工。

A cache memory method and corresponding system for twodimensional data processing, and in particular, twodimensional image processing with simultaneous coordinate transformation is disclosed.

本发明公开了一种用于二维数据处理特别是同时进行坐标转换的二维图像处理的高速缓冲存储器方法及其对应的系统。

The Company consolidated its data processing systems with the opening of a new state-of-the-art data processing center in Clinton, N.J.

位於新泽西克林顿市的新数据处理中心揭幕，成功整合公司的数据处理系统。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。