查询词典 in shape

Based on the previous research on the portal crane administration, one standpoint put forward in this paper is idea that is on the foundation of reliability in this paper, two viewpoints take shape when reason is analyzed, that is fatigue break and appearing the flaw that will extend. What is the fatigue break?(this phenomenon is always happen in some place),the fatigue is that board appears apophysis and concave when the board is pressed .so that the board ability of bearing the weight of load will descend. Second , the board appear the flaw that the flaw extends in the some place of board one reason is that the machine works too long, so the board ability of bearing the weight of load will decline.

本论文建立在已有的港口装卸机械管理的研究基础之上，进一步提出了以可靠性为基础的港口装卸机械的管理思想，已有的研究表明，港口机械设备破坏主要由于两个原因，第一是稳定性问题，特别是构件的局部稳定性，所谓稳定性是指：在板的平面内，板受到平行于板面的压力作用，使板发生隆起、内陷等凹凸不平的结果，从而使板受载能力减弱；第二是结构出现疲劳裂纹及其扩展，这是由于设备长时期运行，而造成设备某些部位出现裂纹并得以扩展，使设备承载能力下降。

Irregular shape with more apophysis.

呈不规则状、有较多突起。

Place the applique onto your apron, pin it down, and sew it down with a topstitch around each shape.

放置在你的围裙的贴花，针下来，和缝制周围每个形状topstitch下来。

Solani, infection cushion and appressorium formed in 24 h, and presented the water-damaged shape mottling.

接种后24 h就可以形成侵染垫和附着胞，出现水渍状斑块。

Stability analysis of Sanjiaoping slope under diverse work condition indicates that the result of strength reduction method is approximate to classical limit equilibrium method. The shape and the position of sliding surface are similar. So, the suggested method is rational.

通过对三交坪边坡不同工况下的稳定性分析表明，强度折减所确定的边坡安全系数与传统极限平衡法所得的结果十分接近，滑面的形状及位置也极为相似，因此认为该方法是合理可行的。

During isothermal extruding of blank, in order to make the material fill successfully into the mold cavity and demould successfully, by using dressing on curved surface of the globoid cams and adopting circular arc transition on each connection, the blank with high precision and shape approximate limit was obtained.

在毛坯等温挤压过程中，为使材料顺利地充满凹模型腔以及成形后脱模顺利，通过在弧面凸轮曲面上加盖敷料及在各连接处采取圆弧过渡，以制得高精度的近似净形零件毛坯件；并采用MSC。

The relationship between transient response and shape design variables is highly non-linear, and the behavior of feasible domains is often not good, which may cause convergence difficulties. In order to improve convergence speed of iteration process, some algorithms the feasible domains adjusting, the adaptive move limit, the approximate line search and the approximate reanalysis, are adopted.

采用基于Newmark积分的直接求导法计算瞬态响应灵敏度，在序列二次规划算法中采用了可行域调整、近似—维搜索、自适应运动极限等改进技术，提高求解效率和收敛稳定性，以解决结构动态响应与设计变量的关系复杂、高度非线性，优化可行区域的性态不良等问题。

The parameters A, B, C and D define the shape of the curve for the function and the values for a fit to theArcSin approximation with minimal error must be found.

参数 A， B， C 和 D 决定了函数曲线的形状。在近似的 ArcSin 中，在最小误差允许范围内，肯定存在这些值。

This paper is devoted to the development of a new meshless method based on a new approximation of shape function.

主要工作是推导了一种基于新的形函数形式的无网格方法。由于目前的无网格方法中，紧支域的大小和形状不同直接影响整体场函数的分布，有时会造成计算结果的严重失真。

In any case, this rock gave evidence that the presbyterium or sanctuary proper was in the shape of a platform which took up not only the apse but an area in the central nave also.

这石头给适当的证词：长老之所或圣所占用的这平台，它不只是在半圆壁龛，还占用部分中殿的范围。

Objective:To explore the feasibility of laparoscopy in diagnosing and treating of abdominal diseases.

目的：探讨腹腔镜用以诊断腹部外科疾病及选择治疗方案的可行性。

The lifetime of nylon 1010 and nylon 1010/POSS composites decreased with increasing temperature.

热重-红外联用分析表明尼龙1010在氮气气氛下的降解产物主要为小分子的低聚物，POSS并不改变尼龙1010降解产物的组成。