查询词典 in shape

Based on the recovered 3D shape, the "texture image" calibrated to a standard illumination is generated by spherical harmonics ratio image and finally the illumination independent 3D face is reconstructed completely. The proposed method combines the strength of statistical deformable model to describe the shape information and the compact representations of the illumination in spherical frequency space, and handles both the pose and illumination variation simultaneously.

基于此重建的3D形状，进而通过球面谐波商图像的方法估计输入图像的光照属性并提取输入图像的光照无关的纹理信息，从而将光照无关的3D人脸完全重构出来，生成输入人脸图像在标准姿态和光照条件下的虚拟视图，用于最终的分类识别，实现了对光照和姿态问题的同时处理。

Clavicle bone is suitable for implant as its density,and for the repair of mandibular defect as its shape.The accurate data of personalized clavicle shape and bone density can be measured through preoperative imaging.It can be used for design of mandibular defects repair and / or tooth plant in the same period with pedicle sternocleidomastoid muscle.

锁骨的骨密度适合做种植牙修复，锁骨的外形适合做下颌骨缺损修复，术前对影像学资料进行丈量能取得个性化的锁骨外形及骨密度的较为正确的数据，对临床上利用带血供的胸锁乳突肌锁骨瓣修复下颌骨缺损和/或同期种植牙修复具有一定的指导意义。

This region of support values shape function is shape function is not zero in the region ...

这种数值形函数的支撑域是指形函数不为零的区域，。。。

In littler reduced area difference it transformed symmetric shape of a sphere enclosing above and below two smaller spheres into asymmetric shape.

我们通过研究发现，上下对称性确实被打破，但只在约化面积差较大时转化到胃形泡；在约化面积差较小时，则转化到上下不对称的双内陷形状。

One of the key challenges in deformable shape modeling is to estimate a meaningful average or mean shape from a set of unlabeled shapes.

可形变形状模型化的一个关键问题就是从一系列未标记的形状点集中估计一个有意义的平均形状。

For the three kinds of abnormal-shaped catalyst particles used,i.e.,ring,wheel shape and honeycomb shape,difference of 2.03 times was found in the pressure drop due to viscous resistance and form drag,and up to 2.7 times due to inertial resistance.

本文所选用的三种异形催化剂的颗粒形状可使粘性力引起的床层压降相差约2.03倍，使惯性力引起的床层压降相差约2.7倍。

A computer-aided system is developed to predict solder joint shape in microelectronics interconnection, and visuality of predicting and analyzing solder joint shape is realized.

提出并设计了焊点形态的剖视分析方法，以RCChip焊点为例，考察了焊点结构参数对焊点三维形态的影响规律，并进行了试验验证。

Single layer ringlike fabric was formed in accordance with the cone shape with high productivity and low cost . This type of fabric can be used to wind cone shape composites conveniently .

可按照锥形件的外廓形状生产单层环形织物，生产效率高，设备费用低，生产的预成型织物可以方便地缠绕成型锥形复合材料。

By means of sem, it is found that in the portland cement clinker with high quality, the alite take the shape of trigonalrhombohedron,and belite shows the shape of irregular ovum, also with the parallel and cross twin-crystals.

借助于扫描电子显微镜发现优质硅酸盐水泥熟料中A矿呈复三方偏三角体形貌特征；而 B矿则呈不规则的浑圆状，并且从外层可看到平行双晶和交叉双晶共存。

On the basis of previously research, this paper re-probe into the mechanism of electro-chemist mechanical manufacturing process, making the rational technological parameter, and developing the manufacturing equipment. Through a lot of technology tests, get a lot of labratory data, accordingly, researched the surface feature of the electro-chemist manufacturing process, and deeply discussed its influence on the work piece feature. The last result is that: the electro-chemist mechanical manufacturing process can reduce the low-frequency component significantly, but on high-frequency component, it has little influence, having obviously positive pole flat effect. After manufacture, the tip parts on the surface of the work piece is cut off, there is micro "high land" shape, the parameter for surface roughness is reduced a lot, the surface outline of the work piece is negative, the bearing length rate is cliffy. Also the surface quality of the work piece is improved. This can help to avoid changing the shape, improve the feature of rub, gear and reduce the time to suit. This would also ensure the precision and result in a longer work piece life.

在以前研究的基础上，本论文重新探讨了电化学机械复合光整加工工艺的机理，确定了较合理的工艺参数，对电化学机械复合光整加工设备进行了改进，通过工艺实验广泛地搜集了大量实验数据，依据实验数据，多角度地研究了电化学机械复合光整加工的表面形貌特点，并且从理论上深入讨论了电化学机械复合光整加工表面形貌对工件工作性能的影响，最后得出的结论为：电化学机械复合光整加工对工件原始表面的低频成分有较大程度的降低，而对高频成分影响较小，有明显的阳极整平作用，被加工工件表面的尖峰状凸起被去除，工件表面呈现出微观&高原型&，表面轮廓不平度高度特性参数大幅度降低，工件表面轮廓分布集中，且呈负偏态，轮廓偏斜度为负值，轮廓支承长度率曲线陡峭，工件的表面质量得到综合改善，这对提高零件的抗接触变形能力、改善摩擦、磨损性能、降低工件的磨合时间、提高工件的精度保持性、延长工件的寿命均有利。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。