查询词典 immovable joint

Flange joint bolt is just put in from the side of flange joint component, nut screw in from the side of flange of coupling.

法兰连接螺栓只能从被连接构件的法兰侧放入，螺母从联轴器的法兰侧拧入。

Joint type of this valve is flange joint.

本阀连接方式为法兰连接。

Pointing to some problems such as easy defect of joint, big pushing to voltage of power net and frequent defects existed in hydraulic station control system of BF, the reforming included replacing pressure meter with electric joint by pressure transmitter with intellectual digital display, replacing alternating contactor by alternating frequency conversion technique and increasing relay control to 984PLC control has been done in Jigang.

针对高炉液压站控制系统存在的接点易损坏、对电网电压冲击大、故障频繁等问题，改造采用带智能数显表的压力变送器代替电接点压力表，应用交流变频技术代替交流接触器，并将继电器控制升级为984PLC控制。

Comparison was made about the clinical performance, such as 10 meters walking time, patient self-appraisal, squat activities and sporting pain, joint swelling, joint effusion and bone friction sound of the three groups of patients before treatment and one months, three months, six months, one year after treatment.

对比观察三组患者治疗前和治疗1月、3月、半年、1年时10米步行时间、患者自我评价、下蹲活动及运动疼痛、关节肿胀、关节腔积液、骨摩擦音等临床表现。

The suitability of the different processes was analyzed by observing the weld appearance,studying the microstructure and measuring the mechanical properties of the joint.The results show that a favorable weld can be obtained under the suitable parameters by laser beam welding or tungsten inert gas welding with filler metal.The TIG welded joint has a wider HAZ,and the laser welde...

试验结果表明：在工艺参数合适的条件下，加焊丝TIG焊和激光焊均能获得成形较好的焊接接头；TIG焊接头热影响区较宽，焊缝深宽比小，而激光焊时热影响区不明显，焊缝深宽比大；两种焊接方法所获得的焊缝区组织均为均匀的等轴晶，但激光焊时焊缝组织更细，从而使接头抗拉强度大幅度提高，达到母材的94%左右。

The equal rigidity design for the flexible joint of DTG is discussed in this poper,which derived the equations of calculating the axial and radial rigidity of two gimbal flexible joint inthis paper.

本文讨论了动力调谐陀螺仪挠性接头的等刚度设计，导出了双平衡环动调陀螺挠性接头轴向刚度和径向刚度的计算公式。

I got a mail which contain the information of developing a kind of new head joint from a friend who always sent me mails before, it likes old Chedeville head joint, made with the same material, and it can make more shake.

我从一位常给我写信的人那里收到了一份介绍一种新开发专业笛头的函件，它类似于老的 Chedeville 笛头，用同样的材料制造，并应该能够产生更多的震动。

Measurement should be done after each step to properly correct the deformity and avoid secondary instability. Alignment of the femur and tibia should be correct to ensure the center of the femoral head, knee joint and ankle joint at the same line.

结果显示对于严重的膝内外翻畸形和屈曲畸形的患者，软组织松解平衡应有计划、分步骤地进行，每完成一步都要进行测量，要做到既纠正到位，又不可过度纠正造成关节继发不稳定。

The results show that laser-arc welding can achieve full penetration by single-path butt jointing through appropriate parameters; Y shape groove with 8 mm truncated edge can enhance the penetration ability of laser-arc hybrid welding. Low welding speed is good for penetration, however the limitation still exists for hick plates joint. Gap is significant factor of penetration when work pieces is large thickness. The hardness of thick plates joint shows that there is big difference in mold of vertical thermal cycle using laser-arc hybrid welding.

结果表明：通过激光功率等焊接规范匹配，激光-电弧复合焊接能实现20 mm厚板的全熔透单道对接；钝边为8 mm的Y形坡口有助于提高厚板激光-电弧复合焊缝熔透能力；降低焊接速度有利于提高熔深能力；工件厚度较大时，装配间隙对焊缝熔深能力的影响较为显著；接头硬度表明厚板激光复合焊焊缝纵向热循环模式存在较大差异。

The purpose of this study was to examine the maximum value of pulling-force, momentum, ground reaction force, net muscle joint moment, the changes of muscle power on raising movement after sitting by different sitting distance patterns, which was measured from feet to a supposed vertical point on hip joint (25cm.35cm.45cm) during Tug-of-War.

中文摘要本研究针对拔河坐地起身动作，以足跟至髋关节点垂直地面位置的不同坐地距离（25公分、35公分、45公分）探讨起身动作之最大拉力值、冲量值、地面反作用力、净肌肉力矩、肌肉功率的变化，藉以了解坐地距离之变化对起身动作之生物力学影响。

We got alerted a couple of times while we were down south that HETs were on the way to bring us back up north because things were going to go hot again, but it was just rumors.

南下的途中我们不只一次得到警告说重型装备运输车将拉着我们重新北上，因为局势正在变得重新紧张起来，但这只是谣传。

It's the one where they find the ghost in the salt mine.

这一集是演他们在盐矿找到鬼