查询词典 igniting

In this paper, the two kinds of hot wind igniting and combustion-supporting technique were summarized.

通过对烧结机两种热风点火助燃方式的项目总结，简要介绍了烧结余热用于点火炉进行热风点火助燃的研究和实际效果。

Not only will you have a new moon igniting this secret endeavor, but also you will finally have Mars going out of retrograde from March 10 on.

你不仅有一个新的月球点燃这个秘密的努力，而且你终于走出去火星逆行的从3月10日。

The 30 books listed here are of unparalleled prose, packed with wisdom capable of igniting a new understanding of the world.

这里列出的30本图书都是无与伦比的、充满智慧的宝库，它向我们打开了全新了解世界的窗口。

What is vital is for Venezuelans to find a way to prevent the coming economic crisis from igniting violent political conflict.

现在对于委内瑞拉重要的是阻止将要爆发的经济危机，而引发政治暴力冲突。

This could push long-term rates and mortgage rates higher, thereby igniting another crisis.

这将推高长期利率和抵押贷款利率，并引发下一场危机。

Our schools will have the highest standards in the world, igniting the spark of possibility in the eyes of every girl and every boy.

我们的学校将会拥有世界上最高的标准，点燃起每一个男女儿童眼中的希望。

The purpose of this research is to pursue an igniting mechanism of Chinese rural consumption market, which is helpful to the coordinate development of agriculture and industry, urban and rural as a whole.

本文研究的目的就是要探求工农、城乡统筹协调发展的农村消费市场启动机制。

When compensating devices are switched by vacuum switches, if they are switched on group, the inrush current can be controlled by inserting suitable current-restrained reactance in-series. Since the restriking overvoltage is pertinent to the capacity of compensating devices and the time of restriking and igniting, the overvoltage can be restrained by arresters with asterism connection at the entrance of the capacitors. Although switching capacitance devices will bring up high interception cross overvoltage, the metal-oxide arrester can limit this overvoltage in the system designed in the thesis, and naturally the compensating devices can operate normally.

使用真空开关投切并联无功补偿装置，在分组投入并联电容器时，串联合适的限流电抗，合闸涌流可以得到控制；重燃时的过电压值与并补装置补偿容量，重燃发生时刻和燃弧时间有关，电容器进线端的三星接法避雷器可以抑制其过电压；切并联电抗器时会产生较高的截流过电压，金属氧化物避雷器可以使本文中所建系统的截流过电压得到限制，并联无功补偿装置可以正常切合。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

By analyzing the igniting characteristics, spreading characteristics and maintenance-fire of the litters, the paper also studied their physical properties, fuel bed characteristics and temperature changes.

通过分析凋落物的物理性质、可燃物床特性及阴燃过程中的温度变化数据，研究了3种凋落物阴燃的引燃特性、持火力和蔓延特性。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。