查询词典 hydraulic pressure

Depending on the fluid volume and precharge pressure of the accumulator, a limited amount of hydraulic energy is then available independent of any other power source.

根据储能器的流体体积和预充气压力，可获得某限定数量的液压能量而不依赖任何其它动力源。

Bleed air is extracted from the high pressure compressor for the following system: Air-conditioning Cabin pressurizatin Wing and engine inlet cowl anti-icing Hydraulic tank pressurization Potable water tank pressurization Fan air is used as cooling air for the precooler to limit the temperature of the bleed air in the pneumatic manifold.

引气从高压压气机中释放给列镣系统：引气从高压压气机中释放给列镣系统：空调系统客舱增压系统 21 专业资料航空工程英语机翼及发动机入口整流罩防冰液压油箱增压饮用水箱增压风扇空气做为预冷器中的冷却空气用以限制增压总管中的引气温度。

In order to do research on pipe flow and pump characteristics of polymer flooding and water flooding rod-pumped well in especially high water-cut stage, rheometric test aimed at production stream from polymer flooding and water flooding rod-pumped well in especially high water-cut stage has been made, and the characteristic of production stream in especially high water-cut stage is confirmed as Newtonian fluid. Experiments using different mediums about pipe flow and pump characteristics is made. Frictional resistance and coefficient of friction resistance of annulus fluid between sucker rod and the pipe flow is calculated under different working conditions. Frictional resistance between plunger and pump barrel under different parameters is calculated based on related theory of pump characteristic and the strained analytical model of oil-well pump. Besides, using the theory of slit flow and hydraulic -clamping pressure, the frictional resistance is calculated, and the error between the result and measured value is no more than 13%.

为研究特高含水期水驱及聚驱抽油机井管流特性与泵特性，本文针对特高含水期水驱及聚驱井采出液进行了流变性试验，确定了特高含水期油井采出液的性质属牛顿流体；利用不同介质，进行管流特性与泵特性试验，得到了不同工况下杆、管环空流的摩擦阻力和摩阻系数；根据泵特性相关理论和抽油泵受力分析模型，计算了不同参数下柱塞与泵筒间的摩擦阻力，并利用缝隙流与液压卡紧力理论对柱塞与泵筒间的摩擦阻力进行了计算，计算结果与实测值误差在13%以内。

Occur such as excessively noisy, running-in procedure, superstandard radial runout and axial movement, working pressure for the sake of interface, operating speed fluctuation, unevenness of faults, in particular supporting the adoption of pneumatic, hydraulic assist devices to different types of power supply unit, energy system, the corresponding interface confidence、regulation allows informization quality, and so on, reaction speed, precision, and so on a more complex South of the mechanical power factors.

出现诸如噪音过大、磨合不佳，超标径向跳动与轴向窜动、工作界面游移，压力起伏波动、运行速度不匀等故障，尤其是配套采用气动，液压辅助装置，以不同类别动力供给装置，能量输导系统、相应工作界面、调控允许质量等的技术状态，反应速度、控调精度等更复杂的因素。

The results indicate: diversion shell can transform the kinetic energy of fluid into pressure energy well, and eliminate the circumferential component of fluid; the inlet incidence angle of vaned diffuser increases at the condition of O.8Q, and it results in flow separation very likely and the hydraulic loss increases; it is nearly non-impact inflow at the condition of 1.2Q, and the velocity distribution is uniform at the inlet of vaned diffuser and flow separation dose not appear.

结果表明：导流壳能很好地将叶轮中流出的流体的动能转化为压能，并消除速度的圆周分量；在0.8Q工况下，空间导叶的进口冲角增大，容易在空间导叶背面产生流动分离，造成水力损失增加；在1.2Q工况下，空间导叶的进口接近无冲击入流，在进口处流速分布较均匀，其内部未发生流动分离现象。

This definitely affects the accuracy of both waer hammer pressure and hydraulic resonance calculation resuLlts.

目前，对非圆形截面，一般都参照圆形截面的水锤波速，进行分析计算，这必然影响水锤压力及水力共振计算结果的准确性。

Wash Down 清洗 3.14.1 Water for the washdown sprays is provided by a water boost pump with precharged hydraulic accumulator and high/low pressure switch.

清洗水的喷射时通过一个带有水压推进器和高/低压力开关的水泵来实现的。

It is important for fracturing design and operation to determine hydraulic fracturing initiation pressure and mode.

确定水力裂缝在井壁处起裂的压力和方式，对水力压裂设计和施工有重要的作用。

Study of effect of hydraulic perforating on formation fracturing pressure［J］.

射孔对地层破裂压力的影响研究［J］。

The main professional equipment are: Braille reflective car number plate mold, high and low pressure hydraulic press, automatic film machine, mimeographs, dryers, tangentially machine, flat screen printing machine to inhale,°machines, large-scale film machine, net machine, plastic blowing machine mill, cooler rack and distribution of Japanese Juroad marking equipment and materials.

主要专业设备有：凸字反光车号牌模具、高低压液压机、自动贴膜机、油印机、烘干机、切圆机、平面吸气丝印机、晒版机、大型贴膜机、拉网机、磨胶刮机、凉架及分销日本菊水牌道路标线设备及其材料。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。