查询词典 hot pressing

Hot-pressing micro-grain boron carbide materials are used in the control system of space navigation. So they are required to be extremely reliabile.

热压微晶碳化硼材料是用于宇航控制系统的材料，对其可靠性要求极高。

Influence of hot-pressing time, temperature and pressure on the porosity and compressive strength of the scaffold.

不同热压时间、温度、压力对支架孔隙率及抗压强度的影响。

It is showed that in the X-ray diffraction patterns of the interlayer solid solution Ti3Si0.9Al0.3C1.93 and Ti3Si0.8Al0.4C1.93 bulk samples,which were in-situ reactively synthesized by hot-pressing the elemental Ti,Si,Al and C mixed powders,the diffraction peaks of [00L] crystal planes are very weak,there is only a small diffraction peak belonging to the [008],and the diffraction peaks belonging...

结果发现，用热压Ti、Si、Al和C混合粉末原位反应合成的Ti3Si0.9Al0.3C1.93和Ti3Si0.8Al0.4C1.93层间固溶体块体样品的X射线衍射谱中[00L]晶面的衍射峰极其微弱，只有[008]面有一个小的衍射峰，[002]、[004]和[006]面几乎没有衍射峰存在，而该块体样品的粉末的X射线衍射谱中所有[00L]晶面的衍射峰均存在。

Texture is obtained by hot-pressing deformation at 700℃ with a deformation rate of 10－4～10－3/s and, with the increment of deformation ratio,(006) texture is further strengthened. In addition, the initial texture of Nd-Fe-B

在700℃，形变速率为10－4～10－3/s的热压变形工艺下，得到以(006)晶面的衍射峰为主峰的织构，即(006)织构，随形变量的增大，(006)织构进一步增强。

The plates are obtained by two steps: compound felt and hot pressing shaping. The opening, mixture, carding, net-paving and needling process that affect shaping process of the blending fiber needle felt are investigated. Then it is concluded that the fiber nets from the BC-272B carding machines are uniform when the rolling speeds of licker-in, cylinder, doffer roller of the roller carding machine are 900r/min, 850r/min and 15.6r/min separately. The fiber needle felt is in a good condition when the paving nets have 8 layers, the type of the felting needle is 30, the density of needling is 1800end/m2, and the depth of needling is 3mm.

纤维复合板材分混合制毡和热压成型两步完成，分别探讨了开松、混合、梳理、铺网、针刺各工序对纤维针刺毡成型的影响，得出BC-272B罗拉梳理机的刺辊转速900r／min、锡林转速850r／min、道夫转速15.6r／min时，从梳理机下来的纤网较为均匀；铺网层数为8层、刺针型号为30、植针密度1800枚／m~2、针刺深度为3mm时，纤维针刺毡的效果较好，纤维复合针刺毡单位面积重量为200g／m~2。

This paper proposed a solution target and lag in hot-pressing time control in order to solve the problem of strong non-linear during the medium-density fiberboard production process.

针对中密度纤维板生产过程中，热压时间控制存在的强非线性和滞后问题，提出了具体的解决方法。

In this paper,the granite polishing abrasive tools are developed and manufactured by hot-pressing,in which powder phenolic resin is used as bond and a few soft materials are used as abrasives.

研制了一种花岗石抛光磨具，该磨具采用粉末酚醛树脂作结合剂和几种软磨料复配混合热压而成。

Our factory has domestic and advanced hot pressing plate production lines.

本厂拥有国内先进的热压板生产流水线。

Veneer hot-pressing dryer, compared with conventional band or roller dryer, is electricity-saving (power at 11 KW), heat-saving (heat consumption at 400,000 Kilocalorie), workshop area-saving (10 M2), and it is also characterized by high production efficiency (daily veneer drying at 20m3), easy-maintenance, and low daily damage.

单板热压干燥机与传统的网带、辊筒干燥机相比，具有省电（功率仅11KW）、省热能（热能消耗仅40万大卡），车间占地面积少（仅10平方米），生产效率高（每天可干燥20m3左右）操作维护简单，日常损耗低等优点，该机的普及必将给单板干燥技术带来新的进步。

That is, the sensitibvity membrane is in operation now coated adhesive, then hot pressing Marigold.

即涂覆膜是在操作时现涂黏合剂，随后热压而得成品。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。