查询词典 hot press

Hot press section consists of a set of the rollers, which a hollow metal drum, naiso electrothermic, temperature can be controlled automatically.

热压部分由一组滚筒组成，其中一只空心金属滚筒，内装电热管，温度可自动控制。

Version before the electrothermic Board clean surface treatment and gilding, pressure on the back of the concaveconvex zinc version designated some skin, a milky white gum toppedwith of the slightly larger than zinc version of cloth version adocumented Zinc plate location and business card printing and membership card modes on the electrothermic, and then you paste in the electrothermic version of Zinc plate cloth top, at the end of platforms put some hard paper on closing and heating power connected to 80-90 ° c hot press about 15 minutes, so that the zinc version bridgeis the electrothermic Board.

装版前应将电热板表面处理洁净，并在烫金，压凹凸锌版背面划一些条痕，将一块涂有乳白胶的稍大于锌版的布块按确定的锌版装版位置和制卡和会员卡制作方式粘贴在电热板上，再将锌版粘贴在电热板布块上面，在底台板上放些硬纸合压，并将电源接通加热至80-90℃，热压15分钟左右，使锌版牢固粘贴在电热板上。

The characteristic of water movement during the process of hot-press drying of bamboo timber was studied.

研究了竹材热压干燥过程中的水分迁移特性。

The company has advanced production processing equipment and the development of strong design, production teams, as well as lean management and complete quality assurance system for a large number of domestic well-known manufacturers provide high-quality hot-press equipment.

公司拥有先进的生产加工设备和实力雄厚的开发设计、生产队伍以及精益的管理和完备的质量保障体系，为众多国内知名厂商提供高品质的热压设备。

The silicon mould was made by wet etching, and then by hot-press method the PMMA microfluidic chip was produced.

在以上研究的基础上，本文制作出了具有新型分叉结构的微流控芯片。

The higher the hot-press temperature and pressure, the higher the cBN content and crystalline perfection were.

而且，随着热压温度、压力和时间的增加，样品中立方氮化硼的含量有明显提高。

Alkaline hot-press oxidization pretreatment technology is an effective pretreatment technology which is widely used in the world for refractory gold ores.

碱性热压氧化预处理工艺是国际上通常选用的可规模开发利用的有效的难选冶金矿预处理技术。

Results show that the bulk nanocomposite magnets are more dense by increasing hot-press temperature, pressure and holding time.

结果表明，增加温度、压力及延长时间都可以使块状复合纳米晶永磁材料致密度增加。

Promoting hot-press temperature properly contribution to not only manufacturing good characteristic particleboard, but creating more value.

因此，适当提高热压温度，不但能制造出性能优良的刨花板还能提高生产率，创造出更多的价值。

Nanoctystalline WC-10Co composite powders were sintered by hot-press sintering at 1360℃.

研究了WC-10Co纳米复合粉的热压烧结，确定合理的烧结温度为1360℃。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。