查询词典 hole

There is a oil groove, a oil hole and two rows of needles in the needle outer ring of wide series, but no oil groove and oil hole in the narrow series which has only one row of bearing unit.

宽系列的滚针轴承外圈有一条油槽，一个油孔，并有两列滚针组。窄系列的有一列滚针组件，没有油槽和油孔。

I Company "times of" series HM1860, HM1860J horizontal plane honing its high precision and high efficiency, wide applicability and easy to operate, and other characteristics, in cars, motorcycles, sewing machines, hydraulic pneumatic, reducer, mold, oil pump Youzui, the internal combustion engine , And other areas within the finishing hole is playing an increasingly big role, and gradually replaced by small and medium-sized hole circular grinding and polishing processes, improved efficiency for users, cost savings, the majority of enterprises are welcome.

我公司&倍力&系列HM1860，HM1860J卧式珩磨机以其高精度、高效率，适用性广和操作简单等特点，在汽车、摩托车、缝纫机、液压气动、减速器、模具，油泵油嘴，内燃机等内孔精加工领域发挥着越来越大的作用，逐步替代了中小孔内圆磨和研磨的工序，替用户提高了效率，节约了成本，受到广大企业的欢迎。

From this he had drawn the inference that this person, once in the forest, had dug a hole with his pick, buried the coffer, and reclosed the hole with his shovel.

蒲辣秃柳儿又猛然想起早晨隐在那荆棘丛中的锹和镐，他跑去瞧，可是锹不在，镐也不在了。

If deviations in excess of 15 degrees hole angle are the result of poorly maintained equipment (such as excessively worn reamers), the hole will be terminated and re-drilled at the CONTRACTOR's expense.

如果超过 15 度井斜角的偏离源自保养不佳的设备，井眼将被终止，而且由承包商自费重新钻井。

The cut-off valve with pilot valve without hand wheel, stem and lift nut inside will guide block and guide slot Butterfly Valves to guide sleeve, the disc-shaped disc to disc type bowl shape, and holes in the bottom of the flap valve to open, the valve cover of the original valve stem hole to hole diversion, because of increased pressure ring, ring, and the valve flap to class mortar, so that the flow passage separated the upper chamber cavity, external cavity, cavity, in the cavity and The external cavity increases with draft tube and stainless steel manual ball valve, flap valve in the cover plate and the center of the end of installing the spring, the upper flap valve install compression seal of the pressure ring, outside the cavity of the wall to open a Drainage holes.

带先导球阀的截止阀无手轮、阀杆和内升降螺母，将导向块与导向槽改为导向套，将盘形阀瓣改为类钵体形阀瓣，并在底部开阀瓣孔，电动蝶阀将阀盖原阀杆孔改为导流孔，因增加压环、密封圈和将阀瓣改为类钵体，使上通流腔分隔为上腔、外腔、内腔，在上腔与外腔的外部加设有导流管与不锈钢手动球阀，在盖板与阀瓣底的中心部加设弹簧，阀瓣上部加设压紧密封圈的压环，在外腔的壁上开有放水孔。

The setting plate 2 is provided with a setting hole 2h for aligning the axis of the piston P with the axis of the cylinder sleeve S, and the setting hole is engaged with the knock pin n of a cylinder block B.

该定位板2具有一个允许活塞P的轴线与气缸套S的轴线重合的定位孔2h。定位孔2h与缸体B上的定位销n相配合。

If anyone break a hole into a house (break-in to steal), he shall be putto death before that hole and be buried.

如果打破房子利用裂缝强行进入住宅偷窃，他必须在那个洞前处以死刑和埋葬。

Iron plow that hole in the pits so Goldman would not make too many adjustments to the operation, hole in the pit of the fundamentals will not be significant change, less risk.

铁犁认为，所以高盛不会对口子窖的经营做出太多的调整，口子窖的基本面不会发生重大改变，风险较低。

Thirdly, on the basis of the productivity model of ideal wells , we comprehensively consider the additional pressure caused by different completion methods and establish four structures of multilateral horizontal wells in 8 different completion methods of the actual open hole completion, slotted liner completion,slotted liner completion with external casing packer, open hole downhole gravel pack completion, openhole prepacked gravel liner completion, casing perforated completion, inside casing gravel pack completion, inside casing prepacked gravel liner completion.

在理想井产能模型的基础上，综合考虑不同完井方式所造成的附加压力损失，建立了这四种分支水平井结构在实际裸眼完井、割缝衬管完井、带ECP的割缝衬管完井、裸眼井下砾石充填完井、裸眼预充填砾石筛管完井、射孔完井、套管内井下砾石充填完井、套管内预充填砾石筛管完井等8种不同完井方式下的产能模型。

The accuracy of the hole point is very important to control the use of the main hole Des support wire, and with the tunnel boring and development, the main branch wire from time to time to check first.

洞口点的精度是非常重要的，洞中的控制采用主辅支导线，并且随着隧道的掘进而向前发展，主支导线要每隔一段时间校核一次。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。