查询词典 hole in one

At this point a thin perspex disc wtih a hole in the centre is positioned so that the apex ofthe tracing lies below the centre of the hole and is attached to the brass plate with sticky wax.

翻译是：结果是，当比赛并没有发现明确的顶端是进一步的动作是必需的。在这一点上一薄有机玻璃盘的中心位置以便先端最最跟踪在中心孔和附属于铜盘用黏稠的蜡。

The asphalt is hard and is dug out with a big scoop shovel or a pick,leaving a hole in the surface of the lake.within a week or two the hole is filled with new asphalt that pushes up from below.the supply of asphalt seems to be endless.

湖中的沥青很坚硬，用大勺铲或锄头挖出后，湖面上便留下了一个洞口。一两周内，洞又被地下涌出的沥青填满了。沥青的供应似乎是源源不断的。

The asphalt is hard and is dug out with a big scoop shovel or a pick,leaving a hole in the surface of the lake.Within a week or two the hole is filled with new asphalt that pushes up from below.

一则古老的传说解释了沥青湖的来历：许多世纪以前，两个印地安人部落打了一次大仗，获胜的部落建立了一个村庄，并举行胜利庆典，他们杀死了数以百计的美丽的蜂鸟，吃了鸟肉，并且用鸟的羽毛装饰他们的衣裳；伟大的圣灵被这些蜂鸟惨遭杀害所震怒，便让全村沉入地下。

Such a tie was to be decided by a hole-by-hole play-off, which was scheduled to be played immediately.

最后的一个名额要通过一洞接一洞的延长赛来决定，而且安排立即进行。

The parts are cast parts. In the processing, it is easier to ensure the processing accuracy of plane than the hole. So the parts' main planes are hole, two blades of the Plectrum and groove.

它的主要加工面是孔、拨叉叉口两端面和槽，在加工中由于面的加工精度要比孔的加工精度容易保证。

The parts are cast parts. In the processing, it is easierto ensure the processing accuracy of plane than the hole. So theparts' main planes are hole, two blades of the Plectrum and groove.

它的主要加工面是孔、拨叉叉口两端面和槽，在加工中由于面的加工精度要比孔的加工精度容易保证。

And in the latter process of working, it also takes hole as the poisoning base and works the two bales of Plectrum, hole, bottom plane, groove and inclined plane. In the entire machining process, it uses separately the milling machine, driller and boring machine.

在后面的工序中，均以该孔为定位基准，加工拨叉叉口两端面、孔、底平面、槽和斜平面，在整个加工过程中，分别采用了铣床、钻床和镗床。

And inthe latter process of working, it also takes hole as the poisoningbase and works the two bales of Plectrum, hole, bottom plane,groove and inclined plane. In the entire machining process, it usesseparately the milling machine, driller and boring machine.

在后面的工序中，均以该孔为定位基准，加工拨叉叉口两端面、孔、底平面、槽和斜平面，在整个加工过程中，分别采用了铣床、钻床和镗床。

In their original form as I saw them in 1994, I would rate the six hole stretch of 10-15 at High Pointe among your top handful of six hole stretches, despite all your subsequent successes.

在原有形式在1994年，我看到他们，我会率尽管你后来成功的6个洞10-15 High Pointe的舒展你的六间孔上方延伸极少数。

Finally, the best values of the diameter of prefabricate hole and extrusion speed is determined through optimize simulation results,In the end, forming experiments study of cold extrusion is processed, experiments results shows that internal thread of C195 knuckle axis can be formed by cold extrusion method, and the extrusion torque is varied when diameter of prefabricate hole and extrusion speed is a series of different value.

最后对挂钩轴内螺纹的加工进行了一系列的实验研究，经过多次实验的失败反复，最终挤压加工出了符合要求的内螺纹；实验结果表明该零件内螺纹时可以采用冷挤压成形方法加工的，并且验证了成形过程中挤压扭矩是随着工件底孔直径和挤压速度的变化而变化的。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。