查询词典 hobbing cutter

Keep the paper good planeness, attention should be paid to the quality of the source from the baguanhe control: one is to maintain the stability of the paper into the paper do not just immediately put into use, it is best to rotate over time to better use the result; the other is stored on paper warehouse and cutter workshop and business card printing and membership card-making workshop of temperature and humidity, to maintain the equilibrium conditions, cannot be placed within a larger geographical imbalance in order to prevent the occurrence of the deformation.

保持纸张良好的平整度，应注重从质量源头上进行把关控制：一是要保持纸张性能的稳定性，刚进的纸张不要马上投入使用，最好旋转一段时间后使用效果较好；二是存放纸张的仓库和切纸车间与制卡和会员卡制作车间的温、湿度，要保持相应的平衡条件，不能存放在较大的悬殊情况，以防止变形情况的发生。

Material-saving pencilwhile using like wooden pencil, The lead core of the nib becomes thick, the available special-purpose cutter is repaired, until the plumbaginous core uses up, The nib is abandoned.

节材铅笔在使用中与木制铅笔一样，使用过程中笔头的铅芯便粗，可用专用刀具修整，直致铅芯用完，笔头弃掉。

In this paper,a new small-sized bit is introduced.The bit is mainly composed of a biassed polyconic cutter,a cylindric roller and two bit legs.

文章介绍了一种新型小尺寸钻头，它主要由一个偏置的多锥形牙轮和一个圆柱形滚轮及两个牙掌组成。

ABSTRACT : In this paper,a new small-sized bit is introduced.The bit is mainly composed of a biassed polyconic cutter,a cylindric roller and two bit legs.

摘 要 文章介绍了一种新型小尺寸钻头，它主要由一个偏置的多锥形牙轮和一个圆柱形滚轮及两个牙掌组成。

The results indicated that ultra-low nitrogen (0.001 0%-0.008 0%, w/%) in low alloy steel could be determined accurately under such optimized analytical conditions as follow: the addition of deoxidizing agent was less than 0.35%, multi-head milling cutter should be chosen and the milling depth was 1.4 mm while sampling, the mass percentage of argon was no less than 99.999 5%, the washing time was set as 8 s, the precombustion time was set as 3. 3 s and energetic precombustion energetic measure optical source mode is adopted.

结果表明，取样时控制脱氧剂加入量不超过0.35%且选用多刀头铣刀盘，铣样深度为1.4 mm；在氩气的质量分数不小于99.999 5%，冲洗时间为8 s，预燃时间为3.3 s，采用高能预燃高能测量光源方式等优化的分析条件下，可有效测定低合金成品钢中质量分数为0.001 0%~0.008 0%的超低氮。

It suggests guarantees that the toolpath of climb cutting can be obtained in consideration of the cutter location surface Zmap model features, thus to gain a qualitied surface.

该算法充分考虑了刀位面Zmap模型的特点，能确保刀具轨迹始终处于顺铣状态，从而保证了良好的加工工艺性。

An Army contract with Cutter Laboratories to reprocess 40,000 packages of outdated dried plasma had gone unexpectedly well.

卡特实验室与军队签订了一项再加工40，000袋过期的干血浆的合同进展地出乎意料地好。

There is a 30 degree lead angle roughing cutter and two 30 degree lead angle finishing and semifinishing cutters.

有一种60°主偏角的粗铣刀具和两种60°主偏角的半精铣/精铣刀具。

Manufactured with imported monoblock tungsten steel, double-edged design and precise grinding technology, it holds such features as no chip adhibited at bottom, lucent and clarified at both sides, permanent rustless of cutter body and long life etc under processing.

特点：本刀具旨在提高产品加工质量和效率，它采用整体进口钨钢制造，双刃设计，精密的刃磨工艺，在加工字体中有底部不留屑，两边光洁透亮，刀体永不生锈，使用寿命长等特点，而且它的刚性上焊接刀具的5倍，这样大大可以加工雕刻速度，再有它可以重复修磨使用，一把刀具至少可以使用一年以上。

The Optimized Design and Reshaping of Profile of Skiving Cutter with Plane Flank for Gleason Gear

由于弧齿锥齿轮尖齿刮削刀盘的切削刃采用斜角直线造形法，其造形误差和重磨误差大，本文提出了优化造形的方法。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48