查询词典 hobber

The third type of formula can only meet the occipital hobber didn't go to an offset printing press for offset press since hobber in regulating rubber roller roller and nano-imprint lithography, clearance between the plate cylinder and penetrated the rubber roller is no need for regulation, walk for offset printing presses in the hobber business card printing and membership card making paper thickness greater than 0.10mm the above with a formula for the calculation and adjustment.

第三栽筹算公式只能满意不行滚枕的胶印机，而行滚枕的胶印机由于在调度橡皮滚筒与压印滚筒之间的间隙之后，印版滚筒与橡皮滚筒之间的间隙必须举行调度，那行滚枕的胶印机在制卡和会员卡制作纸张的厚度大于0.10mm以上不离用第二栽公式举行筹算与调度即可。

We all know that roller, block between hobber and hobber for the imprint, but the artificial division between rolling roller, block roller and embossing roll is a compact, linear three-roll and is consistent, so when the pressure is too large, due to the printing plate is compressed with the roller between a certain amount of sliding friction, thereby allowing the printing plate abrasive.

不小家都懂得，网纹辊、印版滚与不抬印滚之间虽说是滚不抬，但是网纹辊、印版辊与不抬印辊是有不抬缩的，而不一辊的线速量又是分歧的，所以当不弛力过不小时，由于印版被不抬缩会与网纹辊之间爆发必定的滑动摩擦，从而使印版爆发磨损。

From Figure 2 for all we know, the figure is higher than the printed version of the liner, occipital hobber 0.1mm is higher than the rubber blanket, pillow hobber 0.3mm, Al closing?

从图2不未知，该图印版的衬垫矮于滚枕0.1mm，橡皮布矮于滚枕0.3mm，在分不抬时，Al？

When using the die-cutting tool, be sure to use industry gently rolling shouder strickle blankets up drop every day in order to maintain an adequate amount of lubricant die-cutting knife at the end of shouder hobber and the stone the roller surface clean, and in both form a thin film to improve die-cutting knife at the end of shouder hobber and rolls of anvil wear resistance.

搁置模切刀时，一不退给对峙搁置厂家供答的滚肩刮拭毛毡，每天进取滴适度润滑油，以保留模切刀滚肩与底砧辊暗不天的肮脏，且在两者间变成一层薄薄的油膜，恶化模切刀滚肩与底砧辊暗不天的耐磨损性能。

Figure 2 printing plate gaskets is higher than the 0.2 ~ 0.3mm hobber pillow, blanket below the occipital hobber 0.05mm, a2, B2 Department produces a smaller convex hull, of course, less friction and sliding, wear plates, no szlama and "" taping, fault-printing plates and high, less hierarchical dot gain, clearly, the life expectancy of the machine, the electrical power consumed less.

图2印版的衬垫矮于滚枕0.2～0.3mm，橡皮布矮于滚枕0.05mm，在A2、B2处爆发的凹包较小，当然摩擦和滑动也多，印版磨损较多，无不推不净和"杠子"障碍爆发，印版的耐印率矮、网不面放大多，条理纯楚，机械的寿命放大，电机耗电也多。

This paper introduces the method of machining worm gear ,worm with standardized gear hobber.

介绍一种采用标准齿轮滚刀加工蜗轮、蜗杆的方法。

Combined with fault diagnose of the hobber ,a simple and practical method of fault diagnose is brought up,raising its accuracy and efficiency and has better spread value.

结合滚齿机液压系统的故障诊断实例，提出一种简便、实用的故障诊断方法此方法提高了故障诊断的准确性和效率，具有较高的实用推广价

By comparision,the mechanism to improve generating motion precision on CNC hobber by zero transmission is uncovered.

通过比较分析，揭示了通过零传动提高数控滚齿机展成运动精度的机理。

The comparision result shows that the hobber with zero-transmission has inborn dominance on generating motion precision.

研究结果显示，应用零传动技术的滚齿机拥有先天的展成运动精度优势。

Parallel to the vertical flutes in the hobber.

交错于轴向的滚沟槽。

Although translator has turned from being a crystal ball by which the original culture can unrestrainedly penetrate to another crystal ball by which the target culture can freely traverse, the translator's personal embodiment, in the process of cognitive act, are still absent in translation studies. Translators are still subjects without body or simply disembodied subjects.

译者虽然由原语文化可以自由穿透的玻璃球变成了译语文化可以自由穿越的玻璃球，但译者认知过程中的个体体验在翻译研究中依然缺席，译者依然仅仅是一个没有躯体体验的主体。

Chillingly, he claimed our technology is 'not nearly as sophisticated' as theirs and "had they been hostile", he warned 'we would be been gone by now'.

令人毛骨悚然的，他声称我们的技术是'并不那么复杂，像他们一样，和"如果他们敌意"，他警告说，'我们将现在已经过去了。