查询词典 high-profile

Analyzing the change of DH, PCL and active calcium, and selecting each of best method. The results:(1) Dealing with the bone under high pressure ①High content of protein in sheep bone or bone soup:0.05MPa, 2h, 1:2;②Low amino acids in bone powder:0.13MPa, 4h, 1:3; Low amino acids in bone soup: 0.10MPa, 3h, 1:4;(2) Hydrolysis the bone soup with enzymes ①High content of calcium: neutral enzyme, 1500u/L, 6h;②High DH: pancreatic enzyme, 1:100, 6h;③ Low PCL: Pancreatic enzyme, 1:125, 6h; High PCL: alkalescency enzyme,

结果表明：A、高压①骨粉及骨汤蛋白质含量最高：压力为0.05MPa，高压2.0h，骨水比为1：2；②骨粉中氨态氮最低：压力0.13MPa，高压4.0h，骨水比为1：3；骨汤中氨态氮最低：0.10MPa，3.0h，骨水比1：4；B、酶解①游离钙含量最高：中性蛋白酶，酶浓度1500u/L，酶解6h；②水解度最高：胰蛋白酶，酶浓度1：100，酶解6h；③PCL值最低：胰蛋白酶，酶浓度1：125，酶解6h；PCL值最高：碱性蛋白酶，酶浓度1500u/L，酶解8h。

The results:(1) Dealing with the bone under high pressure ① High content of protein in sheep bone or bone soup:0.05MPa, 2h, 1:2;② Low amino acids in bone powder:0.13MPa, 4h, 1:3; Low amino acids in bone soup: 0.10MPa, 3h, 1:4;(2) Hydrolysis the bone soup with enzymes ① High content of calcium: neutral enzyme, 1500u/L, 6h;② High DH: pancreatic enzyme, 1:100, 6h;③ Low PCL: Pancreatic enzyme, 1:125, 6h; High PCL: alkalescency enzyme,

结果表明： A 、高压①骨粉及骨汤蛋白质含量最高：压力为0.05MPa ，高压2.0h ，骨水比为1：2；②骨粉中氨态氮最低：压力0.13MPa ，高压4.0h ，骨水比为1：3；骨汤中氨态氮最低：0.10MPa ，3.0h ，骨水比1：4； B 、酶解①游离钙含量最高：中性蛋白酶，酶浓度1500u/L ，酶解6h ；②水解度最高：胰蛋白酶，酶浓度1：100，酶解6h ；③ PCL 值最低：胰蛋白酶，酶浓度1：125，酶解6h ； PCL 值最高：碱性蛋白酶，酶浓度1500u/L ，酶解8h 。

In the light of cost index and pollution degree, the characteristics of kinds of pulp are analyzed in detail, and the GP pulp which is low cost, high-yield, no-pollution is chosen as the material of tableware. Based on material element analyzed, shaping technology is designed, the to and for single plane shaping equipment which is high shaping quality, high production efficiency and is easy to automatize is chosen. All kinds of measure are taken to solve the problems which are inequality in the shaping process of GP pulp, and dosage which matches with GP pulp is chosen. Some ways of fixing shape and heat up are analyzed, the technology of saving energy of heat pressing to fix shape being composed of oil heat and only one fixed shape in the mold is applied, with which it is high production efficiency, low cost to fix shape effectively, which saves energy 30 percent. In order to make the production line meet with material of GP pulp, measure are taken to solve the problem of pulp adhered to netlike molding which can lead to carry material difficult, the structure of fully automatic equipment is renovated, the loaded beam is optimizationally designed to make equipment structure compactand improve location precision and products quality. According to technologic flow and actual characteristic, Omron PLC is chosen as the core of the control system, proximity switch as detect unit take the place of touch switch, software is designed reasonably according to time order figure, hardware is simplified, the reliability of system is advanced, the stability of system is assured to make production order. Intelligence neuron PID system is studied theoretically which is made up of both neuron with self-organizing and self-learning function and ordinary PID with the characteristic of the simple structure and high stability, which can automatically tune the parameter with the change of system parameter, remain perfect performance.

按成本指标和污染程度分析各浆料的特点，选择低成本、高得率、无污染的磨石机械浆为原料，在原料组分分析的基础上，设计成型工艺，选择成型质量好、生产率高、易实现自动化的往复式单板成型机，采取各种措施解决GP浆成型不均匀的问题及选择与机械浆相匹配的助剂；分析几种定型方式和加热方式，采用定型效果好、生产率高、成本低的油加热与模内一次性定型相结合的热压定型节能技术，节能30％；为了使生产线适应磨石机械浆原料，采取相应措施解决由于粘网造成物料转移困难，对全自动设备结构进行改进设计，着重对物料传送系统的关键部件——承载梁的进行优化设计，使设备更加紧凑合理，提高设备的定位精度和产品质量；根据生产线工艺流程和现场特点，选用OMRON CPM1A型PLC为主核心，接近开关作为检测元件，替代有触点开关，选用可编程终端代替常规面板按扭，并按照时序图科学合理地设计软件，有效地简化系统硬件构成，提高系统的可靠性，保证系统的稳定性，从而使生产更加通畅有序；从理论上探索将神经元应具有的自组织、自学习要求与PID控制结构简单、稳定性好的全自动纸浆模塑餐具生产线的研究特点结合起来，构成神经元自适应PID控制器，当参数的变化时，系统能自行参数整定，保持优良的工作性能指标，满足实际需求。

We are the spirit of "excellent quality, integrity of reciprocity" principle, we know the quality and technology on Product modeling and the importance of constant innovation and focus on high-quality requirements, the introduction of high-quality China-made high-quality steel and steel products "in Guangzhou Industrial Research Institute of Electrical and Mechanical Heat Treatment Technology Research Center "co-operation to provide customers with high-quality steel heat treatment and testing services, including high-quality vacuum hardening, nitriding, carbonitriding, boron nitrogen permeation, soft nitriding, annealing, quenching and tempering,, the high-frequency surface hardening, surface hardening VHF, chemical surface heat treatment, vapor deposition, such as titanium nitride.

我们本著&卓越品质，诚信互惠&的原则，我们深知质量及技术对制模及产品之重要性，不断创新服务及注重高品质要求，推出国产名优钢厂之优质钢材及与&广州市机电工业研究所热处理技术研究中心&合作为客户提供高品质热处理及钢材化验服务，含高质素真空淬火、氮化、碳氮共渗、硼氮共渗、软氮化、退火、调质、中、高频表面淬火、超音频表面淬火、化学表面热处理，气相沈积氮化钛等。

Company's products are as follows: 1, AC-DC transformer test, the control box and console, high-voltage direct current generator, high-current generator, the third-harmonic power generator , AC-DC high-pressure measuring device, dry-type isolation transformers. 2, MOA tester, relay calibrator, DC Resistance Tester, insulating oil dielectric strength tester, dielectric loss tester, insulating oil dielectric loss tester, transformers containing a switch tester. 3, clamp-type ground resistance tester, grounding resistance table, insulation resistance tester, switch mechanical properties tester, loop resistance tester, vacuum tester. 4, cable fault Tester (notebook computers, LCD, kinescope three shows), sentinel-synchronous digital, cable identification device, try扎cable, high-voltage integrated devices, underground pipeline detector, cable detector, high pressure Cable Detector, DC Bridge, DC arms Bridge, the PSA than the bridge. 5, the company also several well-known domestic and foreign agents company's products, for example: Japan has legislation (Xinhua shake table 3121,3122,3123,3125), Japan with 000 (high-voltage clamp-type table HCL1000D, HLC9000, HLC5000, etc.), cable Altimeter instrument, laser range finder, non-metallic pipeline positioning system, and so on. N:-yuan power equipment

公司产品如下：1、交直流试验变压器、控制箱及控制台、直流高压发生器、大电流发生器、三倍频电源发生器、交直流高压测量装置、干式隔离变压器。2、氧化锌避雷器测试仪、继电保护校验仪、直流电阻测试仪、绝缘油介电强度测试仪、介质损耗测试仪、绝缘油介质损耗测试仪、变压器有载开关测试仪。3、钳型接地电阻测试仪、接地电阻表、绝缘电阻测试仪、开关机械特性测试仪、回路电阻测试仪、真空度测试仪。4、电缆故障测试仪（笔记本电脑、液晶、显象管三种显示）、数显同步定点仪、电缆识别仪、电缆试扎器、高压一体化装置、地下管线探测仪、电缆探伤仪、高压电缆探伤仪、直流电桥、直流双臂电桥、变压比电桥。5、本公司还代理国内外多家知名公司的产品例如：日本共立（电动摇表3121、3122、3123、3125等）、日本万用（高压钳型表HCL1000D、HLC9000、HLC5000等）、线缆测高仪、激光测距仪、非金属管线定位系统等等。

One cycle of operation to take Silo body construction, the construction procedure as follows: steel banding to Silo body gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after Silo body pouring until the completion of cycle.

其中筒身施工采取循环作业，其施工程序为：绑扎筒身钢筋至组装好的门架横梁下面—→一次性浇筑混凝土700mm 高—→初滑三个行程（即75mm 高度）—→检查滑出混凝土合适度及滑模系统工作状况—→继续浇筑混凝土500mm 高—→再滑升三个行程—→浇筑混凝土至模板上口—→转入正常滑升，每次滑升500mm 高—→分层交圈绑扎钢筋—→浇筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循环往复直至筒身浇筑完成。

One cycle of operation to take construction, the construction procedure as follows: steel banding to gantry beams assembled below -→ one-time pouring concrete 700mm high -→ early slide three trips (that is 75mm high)-→ check off the concrete slipform system appropriate degree and working conditions -→ continue pouring concrete 500mm high -→ then slip trip or three -→ pouring concrete to template missing -→ normal sliding each slide or 500mm high -→ stratified cross - lap steel banding -→ pouring concrete 500mm high -→ Waterloo or 500mm high -→ 4 in accordance with the procedure after pouring until the completion of cycle.

其中筒身施工采取循环作业，其施工程序为：绑扎筒身钢筋至组装好的门架横梁下面—→一次性浇筑混凝土700mm 高—→初滑三个行程（即75mm 高度）—→检查滑出混凝土合适度及滑模系统工作状况—→继续浇筑混凝土500mm 高—→再滑升三个行程—→浇筑混凝土至模板上口—→转入正常滑升，每次滑升500mm 高—→分层交圈绑扎钢筋—→浇筑混凝土500mm 高—→滑升500mm 高—→按后四道程序循环往复直至筒身浇筑完成。

With this method the copper plating graphite powder was made up in 50% copper content .The silver- copper plating graphite composite was prepared while the silver- copper-graphite composite and the silver-graphite composite were also made up together .The mechanical and electric characteristics of the three kinds of composites were tested and it was found that the copper plating graphite powder can only optimize the properties of the silver matrix composite under the high content of the graphite ,the conductivity and the mechanical property was improved and the material could take higher current in the same carbon content .At 20% carbon content, the resistivity of Ag-graphite composite was 1.67 times as high as that of silver- copper plating graphite composite, the resistivity of Ag-Cu-graphite composite was 3.23 times as high as that of silver- copper plating graphite composite. The bending strength of silver-copper plating graphite composite was 2.17 times as high as that of silver- copper-graphite composite, and the bending strength was 2.11 times as high as that of silver- copper-graphite composite. The wearability of silver- copper plating graphite composite was also enhanced greatly at high carbon content.

利用该方法制备了50%铜含量的镀铜石墨粉，然后进一步制备了一系列相同碳含量的银-石墨复合材料、银-铜-石墨复合材料、银-镀铜石墨复合材料，对三种材料的机械、电气性能进行了综合对比，发现在低碳含量时镀铜石墨粉不能改善复合材料的上述主要性能，而在中高碳含量时则能明显优化复合材料的整体性能，提高了复合材料的电导率，使复合材料在中高碳含量时既具有较高的耐磨性同时也能负载较大的电流，复合材料的机械性能也因镀铜石墨粉的加入而大幅提高，20%碳含量时，银-石墨复合材料的电阻率是银-镀铜石墨复合材料的1.67倍，银-铜-石墨复合材料的电阻率为银-镀铜石墨复合材料的3.23倍，银-镀铜石墨复合材料抗弯强度是银-铜-石墨复合材料的2.17倍，是银-石墨复合材料的2.11倍，同时，在实验给定的条件下，中高碳含量时银-镀铜石墨复合材料的机械磨损耐磨性和通电磨损耐磨性都得以显著提高，银-镀铜石墨复合材料在实验时的接触电压降也更为稳定。

The animal model of this method system have, the characteristics of the high fat, high leptin, high Ins, and match with the characteristic of clinical and the pathologic of simple obesity. This studies showed: The acupuncture can obviously reduce the vaule of intaking food and water of the fat rats, and lower the body weight and fat; The acupuncture can urge the diameter, area, physical volume of white fat cell contract, Brown fat tissue of fat rat group surroundings vascular containing large quantity of white fat cell, the acupuncture group was less. this showed: The acupuncture enhanced the white fat cell metabolism, and promotesed the white fat cell to convert to brown fat cell; The frequency of spontaneous electric of nerve cell of pvn of the fat rat is high, the acupuncture counld depress the spontaneous electric of nerve cell of pvn, This showed: the acupuncture can depress the appetite passing to adjust function of pvn nerve; The monoaminergic neurotransmitter of inside of the fat rat brain is disfunction, the acupuncture can rectify this disfunction, and adjust level of 5-HT, and affect appetite, and improve metabolism; The level of leptin and Ins of fat rat increased high, The level of it of acupuncture group decreased, compared with the fat group p.001, This showed: the fat rats have the defeat of leptin and Ins in the body, The acupuncture can lowering this defeat, The level of leptin and Ins of the fat rat in the brain is less than the normal group, The level of leptin of the acupuncture group is high than the fat group, This showed: the acupuncture can increase the transportation of leptin from blood to brain.

本方法所制肥胖大鼠模型具有高体重、高脂、高leptin和高Ins血症的特点，符合人类单纯性肥胖病的临床和病理特征；实验研究显示：针灸能明显减少肥胖大鼠的摄水、摄食量及降低其体重、体脂；针灸能促使白色脂肪细胞直径、面积、体积缩小，减少肥胖大鼠棕色脂肪组织血管周围白色脂肪细胞数量，显示：针灸增强了白色脂肪细胞的代谢，促进了白色脂肪细胞向棕色脂肪细胞的转化：肥胖大鼠PVN神经细胞自发放电频率增加，脑内单胺递质紊乱，针灸通过抑制PVN亢奋的自发放电，调整5-HT水平，达到影响食欲，改善代谢的作用；肥胖大鼠血中leptin及Ins水平增高，与正常组大鼠比有明显差异，提示大鼠体内存在leptin及Ins抵抗，针灸后肥胖大鼠随着体重体脂的下降，血中leptin、Ins水平降低，与肥胖组比均有显著性差异，而针灸后大鼠脑内leptin增加，与肥胖组比P.05，提示：针灸具有改善leptin、Ins抵抗及增加leptin脑内转运的作用。

China first introduced in the German style of windows and doors and realize the localization of production enterprises in the first domestic product of pure wood, wood kits series of high-grade aluminum windows and doors of the enterprise; first independent development and production of high-end Italian-style windows and doors to the enterprise; The first domestic product in the U.S.-wood, aluminum doors and windows of the series of package-enterprises; first in domestic development and production of wood walls of the family business; first independent development and production of a bullet-proof, anti-riot high-grade security doors and windows; first In the domestic development of intelligent control window and put into application the enterprise; first designed and produced in line with developed Western countries, diplomatic building a high standard and comprehensive prevention requirements of the special windows and doors; first to the United States, Japan and other developed Western countries, exports High-end doors and windows of the enterprise; first in the developed countries to establish branches of the windows and doors manufacturing enterprises in 2000 passed the ISO9001 international quality system certification, and in 2003 for the successful version in 2000 by the British Royal USK international certification in 2001 by Branch Appointed as "Technology Pilot-oriented enterprises" in Beijing in 2003 were rated "famous trademark" in 2003 by Beijing as "a brand-name enterprises" in 2003 was China Building Decoration Association as "well-known brands." Municipal Science and Technology Commission in 2005 was awarded the "high-tech enterprises that certificate" for five consecutive years was in the Trade and Industry Bureau as "Shou credibility of the contract unit."

第一个在中国引入德国风格门窗并实现本地化生产的企业；第一个在国内生产纯木、铝包木系列高档门窗的企业；第一个自主开发并生产出意大利风格高档门窗的企业；第一个在国内生产美式纯木、铝包木系列门窗的企业；第一个在国内开发并生产木质幕墙系列产品的企业；第一个自主开发并生产出防弹、防暴高档安全门窗；第一个在国内开发出智能化控制窗并投入应用的企业；第一个设计并生产出符合西方发达国家外交机构建筑高标准、综合性防范要求的特种门窗；第一个向美国、日本等西方发达国家出口高档门窗的企业；第一个在发达国家设立分公司的门窗制造企业；2000年通过ISO9001国际质量体系认证，并于2003年成功换版；2000年通过英国皇家USK国际认证；2001年被科委评为&科技先导型企业&；2003年被评为北京市&著名商标&；2003年被北京市列为&创名牌重点企业&；2003年被中国建筑装饰协会评为&知名品牌&；2005年获得市科委颁发的&高新技术企业认定证书&；连续五年被市工商局评为&重合同守信誉单位&。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。