查询词典 high pressure

Sixth, followed by release of the cylinder high-pressure injector tubing connector on the nut, the governor of diesel engine running under the handle position, rotation of diesel engine, the high-pressure pipeline from the air (this step can be ignored under normal circumstances, when the start failure should not be ignored).

第六，依次松开各缸喷油器上的高压油管接头螺母，将调速器手柄置于柴油机运行位置，转动柴油机，排出各高压油管内的空气（此步骤一般情况下可以忽略，当启动失败时不应忽略）。

In order to study the effect of high pressure on the quality of fresh pear juice , heating combined high pressure are conducted on fresh pear juice .

为了探讨高压对鲜榨梨汁品质的影响，对鲜榨犁汁产品进行了热协同高压处理。

Keywords: High-pressure metamorphic rocks;High-pressure white micas ;Laser probe 39Ar-40Ar;Excess argon

中文关键词：高压-超高压变质岩；白云母；激光微区氩-氩；过剩氩

High-pressure metamorphic rocks;High-pressure white micas ;Laser probe 39Ar-40Ar;Excess argon

中文主题词：高压-超高压变质岩；白云母；激光微区氩-氩；过剩氩

In diesel engine cylinder, the piston part of the cycle in the compressed gases, and in another part of the work cycle of the combustion gas mixture within the cylinder so the piston top surface expansion high pressure (about 116 ~ 120Kgf/cm2)°under high temperature (about 569°C) gas role, and the pressure through the piston pin, connecting rod to the crankshaft.

在柴油机气缸内，活塞在一部分工作循环压缩气体，而在另一部分工作循环气缸内混合气体燃烧膨胀使活塞顶面承受高温（约569°C）高压（约116～120Kgf/cm2）气体的作用，并把压力通过活塞销、连杆传给曲轴。

The following cases, to go with locator: 1, medium pressure high pressure big time; 2, valve diameter is large Forged Gate, Globe, Check Valves (DN 00); 3, high or low temperature control valve; 4, the action necessary to raise the speed control valve; 5, using standard signal, the operation of non-standard spring when the implementing agency (20 ~ 100KPa spring outside the range); 6, when used for sub-process control; 7, when the valve to achieve the reverse action (air to close each open-type gas conversion); 8, need to change the valve's flow characteristic time (you can change the positioner cam); 9, no spring actuator or piston actuator, the proportion of action to achieve the time; 10, electrical signals to operate pneumatic actuator must Distribution - gas valve positioner.

下列情况下，要配定位器： 1、介质压力高、压差大的时候； 2、调节阀口径大时（DN00）； 3、高温或低温调节阀； 4、需要提高调节阀的动作速度时； 5、用标准信号、操作气动管路截止阀非标准弹簧的执行机构时（20～100KPa以外的弹簧范围）； 6、用于分程控制时； 7、使阀门实现反向动作时（气关式和气开式互相转换）； 8、需要改变阀的流量特性时； 9、无弹簧执行机构或活塞执行机构，要实现比例动作时； 10、用电信号去操作气动执行机构时，必须配电-气阀门定位器。

The following cases, to go with locator: 1, medium pressure high pressure big time; 2, valve diameter is largeForged Gate, Globe, Check Valves (DN 00); 3, high or low temperature control valve; 4, the action necessary to raise the speed control valve; 5, using standard signal, the operation of non-standard spring when the implementing agency (20 ~ 100KPa spring outside the range); 6, when used for sub-process control; 7, when the valve to achieve the reverse action (air to close each open-type gas conversion); 8, need to change the valve''s flow characteristic time (you can change the positioner cam); 9, no spring actuator or piston actuator, the proportion of action to achieve the time; 10, electrical signals to operate pneumatic actuator must Distribution - gas valve positioner.

下面所开列情况下，要配定位器：一、介质压力高、压差大的时辰； 2、调节阀口径大时（DN00）； 3、高温或低温调节阀； 4、需要提高调节阀的动作速度时； 5、用标准旌旗灯号、操作气动管路截止阀非标准弹簧的执行机构时（20～100KPa以外的弹簧范围）； 6、用于分程节制时；七、使阀门实现逆向动作时（气关式和气开式互相转换）； 8、需要改变阀的流量特性时；九、无弹簧执行机构或活塞执行机构，要实现比例动作时； 10、用电旌旗灯号去操作气动执行机构时，必须配电-气阀门定位器。

The structures, materials and the clearance between cylinder and high pressure plunger piston which is used in the small, oilfree, high pressure field are discussed and analyzed.

在分析滑道变形的基础上，采用尺寸链方法综合分析了滑道体、活塞、气缸等的变形对线性余隙容积的影响，提出了减小线性余隙容积的措施。

Then, the method to estimate cavitation erosion characteristic of high pressure piston plunger pump by analyzing impingement angle on outlet of throttling groove is put forward. That is, to hold the impingement angle range of 30°～60°as appraisal criterion of cavitation erosion characteristic on high pressure hydraulic plunger pump.4 The throttling characteristic of hydraulic control valve is studied by CFD calculation and experiment.

最后，提出了一个通过分析节流槽出口处的射流方向来评价高压轴向柱塞空蚀特性的空蚀评价方法，即将节流槽出口的射流角范围30°～60°作为评价高压轴向柱塞泵空蚀特性的标准。4对液压控制阀的节流特性进行了CFD数值计算和试验研究。

A charge of the pneumatic valve engine inspections resumed devices necessary high pressure bottle, if necessary, must add high-pressure air.

1位负责检查引擎气门的气动回复装置所需的高压力瓶，必要时必须补充高压空气。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。