查询词典 heating furnace

In the process of pulverized coal injection into blast furnace, the blowpipe plays an important role in pre mixing the pulverized coal and oxygen, pre heating them and improving the pulverized coal pyrolization and combustion of the coal.

在高炉富氧喷煤过程中，直吹管使喷入的煤粉与氧气预混、预热，并促使煤粉的热解和部分煤的燃烧。

To avoid the complex process and high cost in the current fabrication technique of carbon nanotube display,a 125 μm diametric quartz-glass was fabricated by heating optical fibre to decoat in a sintering furnace and cutting it to 30 mm and 50 mm long.

针对现有的碳纳米管场发射显示器制造技术中存在的工艺复杂、成本过高的问题，利用通信光纤，通过烧结炉热处理的方法制作出了一种直径为125μm的石英玻璃光纤支撑墙，并将其切为30mm、50mm2种长度。

Furnace effective area of 5,300 × 26300mm, the biggest heating capacity of 60 tons / hour.

炉内有效面积 5300×26300mm，最大加热能力60吨/小时。

As the electric furnace water heating system of the complexity of their own, so the use of the system on its real-time simulation of dynamic performance and control law, and so have important practical significance.

由于电炉烧水系统的本身的复杂性，所以利用该系统进行的实时仿真对研究其动态性能和控制规律等均有重要的现实意义。

The effect of switching modes on the entrancement,combustion and billet heating process in furnace were analyzed numerically,and the computational results were compared with production records and onsite measurement,which verified the practicability of this CFD system.

结果表明：采用分段同侧换向控制的HTAC加热炉能获得很好的流场和温度场分布，基本满足高质量的钢坯加热需要，但该炉在生产条件下的温度制度存在不合理之处，在今后设计和操作中应进一步优化和改进；全同侧换向控制的火焰布置方式不利于钢坯的均匀、快速加热；而采用交叉换向控制的火焰布置方式可以改善加热炉内的流场和温度分布，更有利于满足钢坯的加热工艺要求。

A new method to estimate optimum heating operation for reheating furnace is presented in this paper.

提出了计算加热炉最佳加热制度的一种新方法。

There are three time sections for SiC-Si3N4 firebrick processing in electrical resistance furnace, which is called heating, chemical reaction-sintering and cooling section.

电窑中SiC-Si3N4耐火砖的烧制过程按时间可分为三个阶段，即加热阶段、化学反应－烧结及冷却阶段。

Professional manufacturing: electrical circuit board Flashboard frame heat pipe, titanium heating tube, Teflon heaters, precision oven, circuit board hanging tool, circuit board tunnel furnace, SMT equipment, titanium blue.

专业生产制造：电线路板插板架热管、钛加热管、铁氟龙加热器、精密电烤箱、电路板挂具、电路板遂道炉、SMT设备、钛蓝。

That LCA tells us that heating the furnace accounts for 16 percent of glassmaking's negative impacts; the chemicals released into the air from the glass factory run from relatively high levels of carbon dioxide to trace amounts of toxic metals like cadmium.

LCA技术可以告诉我们：熔炉加热环节对环境造成的负面影响比率为16%；而从玻璃制造厂排放到大气中的化合物则从含量较高的二氧化碳到各种痕量金属都有，如镉等。

1 Oven order 5.1.1 first hearth cloth Wind board laying 200mm thickness of the bed material; About Revert cloth laying Wind board thickness 200mm bed material, to prevent Ogive burn plug secondary air pipe; 5.1.2 prior to Add a small amount of flammable wood furnace and left and right back Feeder, ignition Wind Road in oven two days before ignition; 5.1.3 ignition started Ovens need to use a small amount of diesel added to the accumulation of wood, wood ignition when combustible, wood drying to around 200 ° C, according to adjust primer wind baffle and then curves of thermal insulation and heating.

5.1烘炉顺序 5.1.1先将炉床布风板上铺设厚度为200mm的床料；左右返料器布风板上铺设厚度200mm床料，防止把风帽烧坏，堵塞二次风管； 5.1.2事先将少量易燃木柴放入炉膛和左、右返料器，点火风道应在烘炉前2天进行点火； 5.1.3开始烘炉点火时需要用少量的柴油加在堆积的木柴上，点火时木柴易燃烧，木柴烘至200℃左右后，根据情况调节引风挡板，再按升温曲线保温、升温。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。