查询词典 heat-unit

Workshop is ventilated the optimal program that drop in temperature: Below torrid weather, because heat is conducted, heat radiation, did not adopt drop in temperature the indoor temperature of measure wants 10C -20C of prep above outside, manufacturing activity cannot on the rails.

车间透风降冷的最好方法：在酷热气侯下，因为热传达、热辐射、未实行降冷行动的房内温度要高于外面10C-20C，制造项目沒法正常施行。

In chapter 5, heat mechanism and heat radiating forms of the hydraulic system faults are studied. Based on relationship between degree of the hydraulic system faults and thermal image shapes, multi-scale entropy of temperature field is taken to express the fault degree. Entropy of low frequency means its absolute temperature, and entropy of high-frequency means distribution of temperature field.

同时针对系统故障程度的不同，提出了用温度场的熵进行表征的思路，通过多尺度小波对原热场图像进行小波变换，提取其中低频分量的熵用来衡量其绝对温度大小，提取高频分量的熵来衡量其温度场的分布，给出了实验结果，通过实验结果分析，证明这种分析方法是可行的。

On the basis of Equivalent Heat Drop Theory of changeful heat quantity, a mathematical description that heating value enters or leaves thermodynamic system by absolute magnitude has been deduced.

在变热量等效热降法理论的基础上，推导出热质进出热力系统的数学描述———纯热量法。

Objective To explore the effects of heat acclimatization and heat stress on hemorrheology.

目的探讨热应激和热习服对机体血液流变性的影响。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。

Heat and cold can help alleviate pain too, but since moist heat, such as that from a bath, acts differently than the dry heat of a heating pad or the cold of an ice pack, this type of treatment needs to be discussed with a doctor or physical therapist.

热和冷能帮助减轻疼痛太多，但由于湿热，如从一个浴池，行为不同于干热供暖垫或寒冷的冰袋，这种类型的治疗需要讨论的医生或物理治疗师。

This Dragon Filter Heat Shield is made of heat resistant plastics to resist any Heat soak which may occur in daily driving.

本热保护器是由龙锅塑料泡热抵抗任何可能发生的日常驾驶。

In winter, it absorb solar heat energy as solar panel, and form heat barrier in the hollow area to prevent chilliness; In summer, radiant heat of the windows counts 65％ of the total energy consumption, our tailor-made shutter can isolate thermal radiation, save energy loss.

冬季它象太阳能采热板一样吸附太阳热能，在两层玻璃的中空区域形成热屏障，抵御室外寒气；夏季窗口的辐射热要占能耗的65％，而我们的特制窗帘可将热辐射隔绝，抵御这部分损耗。

So far, we human beings for the heating of the concept has long been restricted to convection, conduction, radiation three kinds of surface heating in it, in recent years the use of molecular friction between the object itself is heated and heat of the principle of the developed in the dielectric heating (including the high-frequency and microwave heating) has been widely used in industrial heating and drying purposes above, this heating method unlike the aforementioned three kinds of methods, the heat do not penetrate the surface, but will wear the electromagnetic energy directly to transparent objects into heat inside a method, also known as the fourth heating methods

到目前为止，我们人类对于加热之观念一直都被局限于&对流&、&传导&、&幅射&三种表面加热方法而已，近年来利用&被加热物体本身分子磨擦生热之原理&所发展出来之诱电加热被广泛应用于工业加热干燥用途上面，此种加热方法不像前述之三种方法，热量不需要穿透物体表面，而是将电磁波能量直接穿透物体内部转换成热量的一种方法，也被称为第四种加热方式

Performance of heat pipe for waste heat lithium-bromide refrigerator driven by exhaust gas of diesel engine;2. When refrigerator s and heat pumps run along Carnot cycle, their energy efficiency is highest.

对利用适宜的循环工质实现蒸气压缩式制冷热泵近卡诺循环进行了分析，包括基本思路、可行性分析、典型工质及其特性，并在相同设备条件和工作温度下，对近卡诺循环制冷热泵和普通循环制冷热泵(R22为工质)的效率进行了计算比较，最后对进一步需做的工作进行了探讨。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。